Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 63

Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Скачать руководство пользователя страница 54

OPERATION

54 | EN

www.schmalz.com

30.30.01.00226/03

6

Operation

Local safety regulations apply. In Germany, these include, but are not limited to, Regulation 52 of the
DGUV.
The following work safety instructions do not replace these, but are to be considered as additions:

The following operating steps must be checked by a qualified electrician before
the initial start of operations and section 1.8 (Requirements and instructions for
installation, maintenance and operating staff) must be read.

6.1 General safety instructions regarding operation

DANGER

Electrostatic charge during handling

Risk of explosion

►

The operator must prevent any charge-generating processes.

WARNING

Non-observance of the general safety instructions for normal operation

This can result in personal injury or damage to the system.

►

The system must only be operated by trained personnel who have read and
understood both the jib crane and hoist operating and maintenance
instructions.

► The operator may not leave the control handle of the hoist when a load is

attached to the jib crane.

«
...
52
53
54
55
56
...
»

Содержание SK-JU-110-2000-SRS63-3000-VSL-EX
































































Отзывы:

Нет отзывов