Schleuniger EcoCut 3300 Скачать руководство пользователя страница 45

Страница: 45 / 108

8. Operation of the control software

Reference Manual |Edition 4.0 (10-2013) |EcoCut 3300

45|108

8.6

CONFIGURATION

From the main menu the screen „Configuration“ can

be reached with the key

[3]

. In the „Configura-

tion“ screen all necessary machine settings can be car-

ried out with the following items:

▄

[1]

Devices

▄

[2]

User

8.6.1

Devices

3-1

In this screen the following devices can be activated /

deactivated and the "Combi" function is switched on/

off.

Feeders:

▄

PreFeeder

Marking devices:

▄

HotStamp

Post processing devices:

▄

WireStacker

▄

CableCoiler

Additional screens are activated accordingly.

Combi on / no Combi

With the operation of a wire marker device the wire feeding on the

EcoCut 3300

is interrupted through

the Combi input until the marking procedure is completed, see chapter

"9 Operation using a marking

device (Page 53)"

During automatic processing without a marking device, the feeding on the

EcoCut 3300

is stopped as

long as the switch between pin 4-5 remains closed. The processing continues as soon as this switch is

opened again. See also chapter

"14.2.2 For use with a HotStamp (Page 80)"

Configuration HotStamp

3-1-X

In this screen all parameters for the wire marker device

are determined. See also chapter

"9 Operation using a

marking device (Page 53)"

Distance

In order to correctly position the marking the distance between the two devices must be entered into the

EcoCut 3300

. See also chapter

"9.2.1 Determining the distance (Page 53)"

Содержание EcoCut 3300













































































































Результаты поиска

Содержание EcoCut 3300

Отзывы:

Похожие инструкции для EcoCut 3300

Бренды по названию

Популярные бренды

Schleuniger EcoCut 3300, Справочное руководство

Результаты поиска

Содержание EcoCut 3300

Отзывы:

Похожие инструкции для EcoCut 3300

Бренды по названию

Популярные бренды