Schleuniger EcoCut 3300 Скачать руководство пользователя страница 40

Страница: 40 / 108

8. Operation of the control software

40|108

Reference Manual |Edition 4.0 (10-2013) |EcoCut 3300

8.4

WIRE SCREENS

8.4.1

Wire data 1

After switching on the

EcoCut 3300

the user automati-

cally accesses the screen „Wire“.
The number of wires to produce (Total), the batch (@

batch / @ batch left) with batch size and the wire

length is determined here.
Press

[+]

[OK]

to delete the production status.

Press the key

[×]

to enter the following screens.

8.4.2

Wire data 2

1-X

Here the speed and the ramp (acceleration) with which

the wire shall be transported is determined.

Speed

These settings change the feed speed of the transport; whereas 0 is the smallest and 9 the largest selecta-

ble value.

Table of speeds
Step

m/s

0.1

0.2

0.3

0.5

0.75

1.0

1.2

1.4

1.5

1.6

Ramp (acceleration)

These settings change the ramp (acceleration) of the transport, whereas 0 is the smallest and 9 the largest

selectable value.

Table of ramps
Step

1000

501

334

251

200

167

143

125

111

100

Содержание EcoCut 3300













































































































Результаты поиска

Содержание EcoCut 3300

Отзывы:

Похожие инструкции для EcoCut 3300

Бренды по названию

Популярные бренды

Schleuniger EcoCut 3300, Справочное руководство

Результаты поиска

Содержание EcoCut 3300

Отзывы:

Похожие инструкции для EcoCut 3300

Бренды по названию

Популярные бренды