background image

If You Are Not Familiar With Pinning Small Format Interchangeable Cores

 Schlage  •  SFIC service manual  •  9

7.  With all chambers combinated, turn the plug back to 

the 12 o’clock position so all the pin stacks can fall into 

place. Caution: The bottom of the Schlage keyway is 

very wide and open. Do not turn the plug in a direction 

which would allow the pins to engage in the bottom of 

the key slot.

add 

enough to 

total 23

control 

plus 10 

minus plug 

total

deep op. 

cut minus 

shallow op. 

cut

shallow 

operating 

cut

Top Pin

Build-up Pin

Master Pin

(if any)

Bottom Pin

Memorize:

C 10 - Plug Total + Build Up

Total Stack Height = 23

Plug Total

8.  Add a very small amount of lubricant

1

 into each 

chamber. If using graphite, do not overdo this or the 

springs will not have room to compress properly.

9.  Cap the core:

a.  Slide the core into the capping block.
b.  Install a spring into each chamber.
c.  Slide cap on at the top of each chamber.

Pins fall

into  keyway

Plug turned

too  far

1  Schlage uses FinLub TF from Interflon. Other lubricants can be used, 

however, performance can vary greatly depending on lubricant 

properties.

d.  Chamber by chamber, press the capping tool down 

and strike it sharply with a plastic or rawhide mallet 

to press the cap all the way in and seal the 

chamber. Never use a metal hammer. It will 

eventually ruin your capping block and pin. 

You may prefer to install one cap and drive it into 

place before installing the next. The jolt from the 

mallet can cause loose caps to jump out of place.

10.  Test all three keys (control, TMK and change key).
11.  Spray a small amount of lubricant into the keyway and 

run a key in and out several times to work the lubricant 

through the core. This step is especially important for 

Schlage patented cores. This is the only way to lubricate 

the special side pin.

Plastic or

Rawhide Mallet

Capping Tool

Cap

Spring

Содержание Everest 29

















Отзывы: