Schiller BOB-CAT QUICKCAT 912480 Скачать руководство пользователя страница 9

Страница: 9 / 34

QUICKCAT

MOWERS

SAFETY

BATTERY

Battery acid is caustic and fumes

are explosive and can cause seri-

ous injury or death.
To reduce the risk of personal in-

jury when working near a battery:
– When working with battery

acid, use protective equip-

ment such as, but not limited to,

goggles, face shield, rubber gloves and apron.

– Avoid leaning over a battery.

– Do not expose a battery to open flames or

sparks.

– Be sure batteries with filler caps are properly

filled with fluid.

– Do not allow battery acid to contact eyes or skin.

Flush any contacted area with water immediately

and get medical help.

– Charge batteries in an open, well ventilated area,

away from sparks and flames. Unplug charger

before connecting or disconnecting from bat-

tery.

- Your unit is equipped with an AGM type battery .

An AGM type battery charger should be used on

these when charging.

STORAGE SAFETY

–  Stop the engine and allow to cool before storing.
–  Drain the fuel tank outdoors only.
–   Store fuel in an approved container in a cool, dry

place.

– Keep the machine and fuel containers in a

locked storage place to prevent tampering and to

keep children from playing with them.

– When the machine is to be parked, stored or left

unattended, lower the cutterdeck unless a posi-

tive mechanical lock is used.

– Do not store the machine or fuel container near

heating appliances with an open flame such as a

water heater or an appliance with a pilot light.

– Keep gasoline storage area free of grass, leaves

and excessive grease to reduce fire hazard.

Jump starting

1. Be sure the jumper cables are in good condition.

Turn off the ignition and all electrical accessories

on both machines.

2. Position the machine with a good (charged) bat-

tery next to but not touching the machine with the

dead battery so jumper cables will reach.

3. When making cable connections:

- make sure the clamps do not touch anywhere

except to intended metal parts,

- Never connect a positive ("+" or red) terminal

to a negative ("–" or black) terminal.

- Make sure the cables won't get caught in any

parts after the engines are started.

4. Connect one end of the first jumper cable to the

positive

terminal on one battery. Connect the

other end to the

positive

terminal on the other

battery.

5. Connect one end of the other cable to the

negative

terminal of the machine with a good

(charged) battery. Make the final connection on

the engine of the machine to be started, away

from the battery.

6. Start the vehicle with the good battery, then the

machine with the discharged battery.

7. Remove the cables in the exact reverse order of

installation. When removing each clamp, take

care it does not touch any other metal parts while

the other end remains attached.

WARNING

Содержание BOB-CAT QUICKCAT 912480



































Результаты поиска

Содержание BOB-CAT QUICKCAT 912480

Отзывы:

Похожие инструкции для BOB-CAT QUICKCAT 912480

Бренды по названию

Популярные бренды

Schiller BOB-CAT QUICKCAT 912480, Руководство оператора

Результаты поиска

Содержание BOB-CAT QUICKCAT 912480

Отзывы:

Похожие инструкции для BOB-CAT QUICKCAT 912480

Бренды по названию

Популярные бренды