manualshive.com logo in svg

Schier GB-50, Руководство по установке

Поделиться
Скачать
Schier GB-50 Скачать руководство пользователя страница 4

Schier | GB-50 Installation Guide

page 4 of 10

GETTING TO KNOW THE GB-50

1.

Pickable cast iron cover (standard)

2.

 Cover 

gasket

3.

  Safety Star® access restrictor 

4.

  Safety Star® tether

5.

 Cover 

adapter

6.

  Cover adapter gasket assembly 

with upper and lower stainless 
steel band clamps

7.

  4" cleanout plug (x2)

8.

  Outlet bulkhead connection 

(optional) 4" FPT (x2)

9.

  Bulkhead connection gasket

10.

Bulkhead connection retaining nut

11.

  Inlet diffuser cover (white)

12.

 Inlet diffuser

13.

  Inlet diffuser retaining nut

14.

  Inlet diffuser foot retaining nut

15.

  Inlet diffuser (foot)

16.

  Inlet bulkhead connection 4" FPT

17.

  4" plain end fitting (x2)

18.

  Composite cover bolts 

and washers (x4)

19.

  Bolted composite cover (optional)

20.

 Air relief/visual access

21.

  Outlet diffuser retaining nut 

22.

 Outlet diffuser 

23.

 Outlet diffuser foot retaining nut 

24.

 Outlet diffuser (foot) 

25.

 Outlet bulkhead connection 

(standard) 4" FPT

26.

 7/16" nut driver bit

1

18

19

20

21

22

23

24

10

9

8

7

2

3

5

6

7

8

9

10

13

12

11

15

14

10

9

16

17

26

4

10

17

9

25

Inlet diffuser 
cover (white)

Содержание GB-50











Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды