Scheppach HL2200GM, Перевод оригинального руководства пользователя, Страница: 24 / 120


www.scheppach.com /

service@scheppach.com /

+(49)-08223-4002-99 /

+(49)-08223-4002-58
24 | GB
8. Unpacking
Open the packaging and remove the device carefully.
Remove the packaging material as well as the pack-
aging and transport bracing (if available).
Check that the delivery is complete.
Check the device and accessory parts for transport
damage.
In case of complaints the dealer must be informed
immediately. Subsequent complaints will not be ac-
cepted.
If possible, store the packaging until the warranty pe-
riod has expired.
Read the operating manual to make yourself familiar
with the device prior to using it.
Only use original parts for accessories as well as for
wearing and spare parts. Spare parts are available
from your specialized dealer.
Specify our part numbers as well as the type and year
of construction of the device in your orders.
m
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas -
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
9. Attachment / Before starting the
equipment
9.1 Attaching the three-point bolts
(enclosed accessories bag A) (Fig. 3)
Insert the threaded bolts in the designated holes and
fix them from the other side with an M22 nut each.
9.2 Attaching the drive shaft protective cap (7)
(enclosed accessories bag B) (Fig. 4)
Place the drive shaft protective cap on the protruding
threaded receivers at the drive shaft and secure it
with both M10 nuts.
9.3 Putting the splitter into the work position
(enclosed accessories bag C) (Fig. 5 + 6)
Connect the splitter to the mains power. Be aware of
the motor’s direction of rotation. Lower both control
handles until the cylinder engages with the guide.
Insert the two L-pins (C) to secure the cylinder on
the kindling splitter. Secure the L-pins in the spring
tabs. Then bring the splitting blade to the top position
and remove the support. You must store the support
safely because it is needed every time the splitter is
transported.
9.4 Attaching the supporting arm (13)
(enclosed accessories bag D) (Fig. 7)
Secure the supporting arm with a hexagon bolt
M10x40, two washers and a nut.
Remaining hazards
The machine has been built using modern tech -
nology in accordance with recognized safety
rules. Some remaining hazards, however, may
still exist.
• The splitting tool can cause injuries to fingers and
hands if the wood is incorrectly guided or support-
ed.
• Thrown pieces can lead to injury if the work piece is
not correctly placed or held.
• Injury through electric current if incorrect electric
connection leads are used.
• Even when all safety measures are taken, some re-
maining hazards which are not yet evident may still
be present.
• Remaining hazards can be minimized by following
the safety instructions as well as the instructions in
the chapter Authorized use and in the entire operat-
ing manual.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Release the handle button and switch off the ma-
chine prior to any operations.
• Avoid accidental starts of the machine: Do not
press the start button while inserting the plug into
the socket.
• Use the tools recommended in this manual to ob-
tain the best results from your machine.
• Always keep hands away from the work area when
the machine is running.
7. Technical data
HL2200GM HL3000GM
Drive Drive shaft + e-motor
Motor V/Hz 400V / 50Hz
Input P1 W 5100 5500
Output P2 W 4000 4500
Operating mode S6 40%
PTO shaft / Motor
speed 1/min
540
1400
Phase inverter yes
Dimensions D/W/H 1540 x 1140 x 2520 mm
Log length 1100 mm
Power max. tons* 22 30
Piston stroke 948 mm
Forward speed cm/s 10,5 12,5
Return speed cm/s 7,5 6,7
Oil quantity l 24 30
Weight kg 319 373
Subject to technical changes!