Scheppach DM460T, Инструкция по эксплуатации

Страница: 10 / 108

10 english
Manufacturer
Scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
We wish you much pleasure and success with your
new scheppach machine.
Note
In accordance with valid product liability laws, the
manufacturer of this device shall not be responsible
for damage to and from this device which results from:
• Improper care.
• Noncompliance with the Operating Instructions.
• Repairs made by unauthorized persons.
• The installation and use of any parts which are not
original scheppach replacement parts.
• Improper use and application.
• Failure the electrical system as a result of noncom-
pliance with the legal and applicable electrical direc-
tives and VDE regulations 0100, DIN 57113 / VDE
0113.
We recommend
that you read through the entire operating instructions
before putting into operation.
These operating instructions are to assist you in get-
ting to know your machine and utilize its proper ap-
plications.
The operating instructions contain important notes on
how you work with the machine safely, expertly, and
economically, and how you can avoid hazards, save
repair costs, reduce downtime and increase the reli-
ability and service life of the machine.
In addition to the safety requirements contained in
these operating instructions, you must be careful to
observe your country’s applicable regulations.
The operating instructions must always be near the
machine. Put them in a plastic folder to protect them
from dirt and humidity. They must be read by every
operator before beginning work and observed consci-
entiously. Only persons who have been trained in the
use of the machine and have been informed of the
various dangers may work with the machine. The re-
quired minimum age must be observed.
In addition to the safety requirements contained in
these operating instructions and your country’s appli-
cable regulations, you should observe the generally
recognized technical rules concerning the operation
of woodworking machines.
m
General notes
• After unpacking, check all parts for any transport
damage. Inform the supplier immediately of any
faults.
• Later complaints cannot be considered.
• Make sure the delivery is complete.
• Before putting into operation, familiarize yourself
with the machine by carefully reading these instruc-
tions.
• Use only original scheppach accessories, wearing
or replacement parts. You can find replacement
parts at your scheppach dealer.
• When ordering, include our item number and the
type and year of construction of the machine.
DM460T
Included with delivery
Wood turning machine
Work piece table
Carrier
Rotating tailstock centre
Independent chuck
Mandrel
Tappet
Jaw spanner SW 32/41
Hex driver 3/6/8
Operating instructions
Technical data
Dimensions
L x B x H mm
940 x 270 x 420
Bed height mm
190
Headstock
thread
M 33
Headstock ta-
per
MK 2
Height of cent-
ers above bed
mm
152
Width between
centers mm
457
Diameter
above bed mm
305
Diameter be-
tween centers
mm
240
Length of tool
holder mm
150
Weight kg
34,8
Wood turning spindle with dust-proof precision grooved ball
bearing
Revolutions
1/min
650 / 1000 / 1450 / 2000 / 3000
Tailstock
Tailstock cone
MK 2
Tailstock drill
hole (hollow
spindle) ø mm
9,5
Tailstock
sleeve adjust-
ment mm
47
Drive
Electric Motor
220 – 240V~ / 50 Hz
Input P1 kW
0,55
Output P2 kW
0,30
Revolutions
1/min
1400
Motor protec-
tion
yes
Undervoltage
release
yes
Operating
mode
S1
Noise parameters
Acoustic power level in dB
Idling L
WA
= 74.3 dB(A),
Operating L
WA
= 91.7 dB(A)
Acoustic pressure level in dB
Idling L
pAeq
= 61.3 dB(A),
Operating L
pAeq
= 78.7 dB(A)