Scheppach 5905310902, Перевод оригинального руководства пользователя

Страница: 22 / 156

www.scheppach.com
22 | GB
Functional test
Test the function before every use.
Action: Result:
Push both handles
towards below.
Splitting knife goes down
to approx. 10 cm above the
table.
Let one handle loose,
then the other.
Splitting knife stops in the
desired position.
Let both handles
loose.
Splitting knife returns to
upper position.
Check the oil level before every use – see chap -
ter “Maintenance“.
Venting (fig. 14)
Before working with the log splitter, vent the hydraulic
system.
• Release the venting cap 6 by a few revolutions so
the air can escape from the oil tank.
• Leave the cap open during the operation.
• Before you move the log splitter, close the cap
again in order not to lose any oil.
If the hydraulic system is not vented, the enclosed air
will damage the gaskets and with it the complete log
splitter.
Stroke limit for short logs (fig. 10)
Lower splitting knife position about 10 cm above ta -
ble.
• Move splitting knife to the desired position
• Release one operating arm
• Switch motor off
• Release the second operating arm
• Undo the star grip screw (10a)
• Push the stroke set rod (8) to the top until it is
stopped by the spring
• Tighten the star grip screw (10a) again.
• Switch motor on
• Check upper position
Switching on and off (12)
Press the green button for switching on.
Press the red button for switching off.
Note : Check the function of the ON/OFF unit before
every use by switching on and off once.
Restarting safety in case of current interruption
(no-volt release).
In case of current failure, inadvertent pulling of the
plug, or a defective fuse, the machine is switched off
automatically.
For switching on again, press anew the green button
of the switch unit.
9.2 Fitting the table (5)
• Undo the star-grip screw (Fig. 4)
• Now fold out both side trays (11), as shown in Fig. 5
• Now fit the table in the retainer intended (Fig. 6 (1))
and re-tighten the star grip screws previously loos-
ened (Fig. 6 (2)).
9.3 Fitting the complete control arms (10)
(accessories bag B)
The control handles on the arms point outwards!
• Remove pre-assembled bolt (fig. 7 (C)).
• Grease the top and bottom plates.
• Insert the complete control arm in the position pro-
vided (fig. 7 (1)).
• Guide control arm (A) into the rocker switch (B)
(Fig. 7 (2))
• Secure the control arms completely with the bolts
(C) and fix them with a cotter pin.
• Now fasten the other control arm on the other side
in accordance with the method described
9.4 Fitting the claws
(enclosed accessories bag C)
• Fasten the additional retainers (D) to the claws with
two Phillips head screws, washers and nuts (fig. 8).
Make sure that the larger additional retainer is fas-
tened with the left claw (4).
• Place the adjustable claws on the hexagon nuts
previously attached, and fasten these with the star
grip screws and washers enclosed (fig. 8)
• Note that the prongs on the claws must point to -
wards each other after installation (fig. 9)
m
IMPORTANT!
You must fully assemble the appliance before
using it for the first time!
10. Initial operation
Make sure the machine is completely and expertly
assembled. Check before every use:
• The connection cables for any defective spots
(cracks, cuts etc.).
• The machine for any possible damage.
• The firm seat of all bolts.
• The hydraulic system for leakage.
• The oil level.
Checking the oil level (fig. 13)
The hydraulic unit is a closed system with oil tank, oil
pump and control valve. Check the oil level regularly
before every use. Too low an oil level can damage
the oil pump. The oil level must be within the centre
mark on the oil dipstick. The splitting column must
be retracted before the check, the machine must be
level. Screw in the oil dipstick fully, to measure the
oil level.