Scheppach 5903806850, Перевод оригинального руководства пользователя

Страница: 20 / 80


www.scheppach.com

service@scheppach.com

+(49)-08223-4002-99

+(49)-08223-4002-58
20 | GB
surfaces, when performing an operation where
the screw or attached tool could come into
contact with hidden wiring. Contact between
the screw or attached tool and a live wire may
cause exposed metal parts of the power tool to
become live and give the operator an electric
shock.
8. Additional Safety Warnings
Information on the rechargeable battery
1. The battery pack of the rechargeable device is
not charged when delivered. It is therefore nec
-
essary to charge the battery before first com -
missioning.
2. For optimum battery capacity avoid deep dis -
charge cycles! Charge your battery frequently.
3. Store your battery in a cool place, ideally at 15°C
and with at least 40% charge.
4. Lithium-ion batteries are subject to natural age -
ing. The rechargeable battery must be replaced
no later than when its capacity is just 80% of the
capacity in new condition! Weakened cells in an
aged battery pack are no longer able to cope
with the high capacity requirements and therefore
constitute a safety risk.
5. Do not throw old rechargeable batteries into an
open fire. Risk of explosion!
6. Do not ignite or burn rechargeable batteries.
7. Do not deep discharge rechargeable batter-
ies! Deep discharge damages the battery cells.
The most frequent cause of deep discharge in
battery packs is lengthy storage or a lack of use
of partially discharged rechargeable batteries.
End the working process as soon as the capaci-
ty is notably reduced or the protection electronics
trigger. Only store the rechargeable battery after
fully charging.
8. Protect rechargeable batteries or device from
overloading! Overloading quickly leads to over -
heating and cell damage inside the rechargea-
ble battery housing, without overheating being
externally visible.
9. Avoid damage and impacts! Replace recharge -
able batteries immediately if these fall more than
one metre or if they have been exposed to hefty
impacts, even if the battery pack housing ap
-
pears undamaged. The battery cells inside may
be seriously damaged. Also observe the disposal
instructions here.
10. With overloading or overheating, the protective
shut-down integrated in the device switches off
for safety reasons. Attention! Do not actuate the
on/off switch again if the protective shut-down
has switched the device off. This can lead to
damage to the rechargeable battery.
a) Do not overload the device. Always use an elec -
trical power tool that is intended for the task you are
undertaking.
By using the right electrical power tool for the job you
will work more safely and achieve a better result.
b) Do not use an electrical power tool if its switch is
defective. An electrical power tool that can no longer
be switched on and off is dangerous and must be re-
paired.
c) Pull the mains plug from the socket before you
make any adjustments to the device, change acces
-
sories or when
the device is put away. This precaution is intended to
prevent you from unintentionall starting the device.
d) When not in use always ensure that electrical pow
-
er tools are kept out of reach of children. Do not let
anyone use
the device if he or she is not familiar with it or has
not read the instructions and advice. Electrical power
tools are dangerous when they are used by inexperi -
enced people.
e) Look after the device carefully. Check that moving
parts are working properly and move freely. Check
for any
parts that are broken or damaged enough to detri-
mentally affect the functioning of the device. Have
damaged
parts repaired before you use the device. Many acci -
dents have their origins in poorly maintained electri -
cal power tools.
f) Keep cutting tools clean and sharp. Carefully main -
tained cutting tools with sharp cutting edges are less
likely to jam and are easier to control.
g) Use the electrical power tool, accessories, insert
-
ed tools etc. in accordance with these instructions
and advice, and
the stipulations drawn up for this particular type of
device. In doing this, take into account the working
conditions
and the task in hand. The use of electrical power tools
for purposes other than those intended can lead to
dangerous situations.
Safety instructions specifically for
impact screwdrivers
Wear hearing protection when impact
screwing. Exposure to loud noise can lead
to hearing loss.
Secure the workpiece! A workpiece securely
held by a clamping device or vice is much safer
than one held in your hand.
Hold the power tool firmly. High torques can
occur for brief periods while tightening and
loosening screws.
Wait until the power tool has come to a standstill
before putting it down. The tool can jam,
this leading to loss of control of the power tool.
Hold the power tool by the insulated gripping