www.scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
22 | GB
The specified vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a
minimum.
• Only use appliances which are in perfect working-
order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
•
Switch the appliance off when it is not in use.
• Wear protective gloves.
7. Assembly
Before you connect the equipment to the mains sup-
ply make sure that the data on the rating plate are
identical to the mains data.
Always pull the power plug before making adjust-
ments to the equipment.
Pull the power plug before doing any maintenance
or assembly work on the equipment.
•
The machine must be set up so that it stands firm
-
ly, i.e. it must be securely screwed to a work bench
or similar.
• All covers and safety devices have to be properly
fitted before the equipment is switched on.
• The grinding wheels must rotate freely.
• Check that the voltage on the rating plate is the
same as your supply voltage before you connect
the equipment to the power supply.
Warning! Never connect the plug to power source
outlet until all installations and adjustments are com-
pleted and you have read and understood the safety
and operation instructions.
Tool support (left and right) (Fig. 1, 2, 2.1)
Fasten the tool support (4) to the grinding wheel
guard (6) with the wing screw (a) and washer (b).
The distance between wheel and work rest should
not exceed 2 mm.
Spark guard with LED work lamp (left and right)
(Fig. 1, 3)
Fasten the spark guard (2) with LED work lamps (5)
to the grinding wheel guard (6) with two M5x8 pan
head screws (c).
The distance to the grinding wheel (3) should be not
more than 2 mm. The distance between the spark
guard (2) and the grinding wheel (3) can be adjusted
by slackening the two pan head screws (c). Tighten
the screws securely.
6. Technical Data
Delivery
Bench Grinder
User’s Manual
Technical Data
Dimensions L x W x H
mm
410x260x290
ø grinding disc max.
mm left/right
200/200
ø grinding disc
min. mm left/right
(after wear and tear)
160
ø grinding disc bore
max. mm
15,88
grinding disc width mm
left/right
20/40
Lamp
LED with battery (2x)
Weight kg
13
Motor
Motor V/Hz
230-240/50
Input power
S2 10 min W
500
Motor speed 1/min
2850
Subject to technical changes!
Load factor:
A load factor of S2 10 min (intermittent periodic duty)
means that you may operate the motor continuously
at its nominal power level (500 W) for no longer than
10 minutes ON period. If you fail to observe this time
limit the motor will overheat. During the OFF period
the motor will cool again to its starting temperature.
Sound and vibration
Sound and vibration values were measured in ac-
cordance with EN 62841.
L
pA
sound pressure level
62,4 dB(A)
K
pA
uncertainty
3 dB
L
WA
sound power level
77 dB(A)
K
WA
uncertainty
3 dB
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with EN 62841.
Vibration emission value a
h
≤ 2.5 m/s
2
K uncertainty = 1.5 m/s
2
Warning!
The specified vibration value was established in ac
-
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the specified value in excep
-
tional circumstances.
The specified vibration value can be used to com
-
pare the equipment with other electric powertools.
