Y-NOT SPLIT-IT MOUNTING INSTRUCTIONS
SCHAFFERT MFG. CO., INC.
308-364-2607
OR
800-382-2607
71495 rd. 397 ∙ indianola, ne 69034 ∙ 308-364-2607 or 800-382-2607 ∙ fax: 308-364-2410 ∙ [email protected] ∙ www.schaffert.com ∙ 20 apr 2020
Before working on your planter or drill
DANGER:
When storing or working on the planter always install cylinder stops or place the planter on stands to prevent personal injury or damage to the attachments.
PLEASE:
Read instructions completely and verify all package contents before beginning installation.
For Planters
SCHAFFERT MFG. CO. INC. - phone: 800-382-2607 - fax: 308-364-2410
70
Rebounder covered by one or more of the following U.S. patents: 5,640,915; 5,918,557; 6,082,275; 6,283,050; 6,453,832, 6,763,773 and 7,121,216.
7 1 4 9 5 r d . 3 9 7 - i n d i a n o l a , n e 6 9 0 3 4 - p h o n e : 8 0 0 - 3 8 2 - 2 6 0 7 - f a x : 3 0 8 - 3 6 4 - 2 4 1 0 - i n f o @ s c h a f f e r t . c o m - w w w . s c h a f f e r t . c o m
Y-NOT SPLIT-IT MOUNTING INSTRUCTIONS
Optional Fitting for Rebounders
(Read Instructions Completely before Beginning Installation)
Mounting Instructions
Before you begin locate the “package contents” list to verify all items are included.
Step #1:
take the propeller t-nut
(fig. (a))
and insert it into the hole on the backside of the
Rebounder saw tooth insert (
fig. (b)
using a hammer or pliers to press it into the
plastic.
Step #2:
turn the saw tooth over placing it into the Rebounder (see Rebounder mt. instruc-
tions for proper placement of the saw tooth). Now place the L-bracket (
fig. (c)
) with
the small hole on the Rebounder with the washer (
fig. (d)
) on top, over the hole of
the propeller tee nut.
Step #3:
using a screw driver, tighten the round-head, slotted (10-24 x 3/8”) screw (
fig. (e)
)
into the propeller t-nut.
Step #4:
using a hair dryer on low or medium setting, briefly heat the short piece of clear
hose. Quickly push heated end of this hose all the way over the barbed end of the
“Y”
(fig. (f)
).
Step #5:
install the clear hose and “Y” between the raised area that holds the screws. The
“Y” should bump up against the molded - in tab
(fig. (g)
).
Step #6:
place the metal plate over the clear hose and install the 2# 12x3/8” Pan Phillips
type screw into the holes of the Rebounder.
Step #7:
after mounting the first Rebounder with the Y-Not check to make sure that the out-
lets on the Y-Not do not extend past the edge of the Rebounder. Trim with a side
dike (
fig. (h))
. Clean out the holes with a pocket knife after clipping, this will keep
the Y-Not from plugging.
Step #8:
if you prefer to have the fertilizer closer to the bottom of the seed furrow you can cut
the molded in tabs off (
fig. (i))
. Slide the Y-Not closer to the end of the Rebounder
before tightening the screws on the metal plate. Then refer to step 7. Normally this
is only done for inoculants. Refer to Hose Holder Instructions as it will do what cut-
ting tab off will do.
Important Points to Remember:
- do not over-tighten or bottom out the screws into the Rebounder as this can damage the plastic.
-
IMPORTANT!! Do not strap any large tie around any part
of the hose
, this 1/4” hose must be able to flex with the Rebounder
independently. Hose holder kits are available for securing the hose.
-
NOTE: screws shown below come in the Rebounder Kit.
Y-Not Split-It Package Contents
for JD type (per single row)
Item
Quantity
“Y” . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1/4 Black Hose . . . . . . . . . . . . . . . . . . 1
3/8” Clear Hose. . . . . . . . . . . . . . . . . . 1
Metal Plate. . . . . . . . . . . . . . . . . . . . . . 1
L-Bracket . . . . . . . . . . . . . . . . . . . . . . . 1
Washer . . . . . . . . . . . . . . . . . . . . . . . . . 1
Propeller T-Nut . . . . . . . . . . . . . . . . . . . 1
Screw for T-Nut Slotted . . . . . . . . . . . . 1
Instruction Sheet . . . . . . . . . . . . . . . . . 1
Y-Not Split-It Package Contents
for IH 800/900 type (per single row)
Item
Quantity
“Y” . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1/4 Black Hose . . . . . . . . . . . . . . . . . . 1
3/8” Clear Hose. . . . . . . . . . . . . . . . . . 1
Tie Strap . . . . . . . . . . . . . . . . . . . . . . . . 1
Metal Plate. . . . . . . . . . . . . . . . . . . . . . 1
Tube Clamp . . . . . . . . . . . . . . . . . . . . . 1
Instruction Sheet . . . . . . . . . . . . . . . . . 1
Y-Not Split-It Package Contents
for IH 1200 type (per single row)
Item
Quantity
“Y” . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1/4 Black Hose . . . . . . . . . . . . . . . . . . 1
3/8” Clear Hose. . . . . . . . . . . . . . . . . . 1
Tie Strap . . . . . . . . . . . . . . . . . . . . . . . . 1
Metal Plate. . . . . . . . . . . . . . . . . . . . . . 1
Instruction Sheet . . . . . . . . . . . . . . . . . 1
fig. (h)
JD type
Rebounder
Drill type
Rebounder
fig. (i)
Y-Not
installed and mold-
ed-in tab removed.
NOTE: THIS IS NOT
RECOMMENDED IN
MOST CASES
IH type
Rebounder
fig. (d)
fig. (b)
fig. (c)
fig. (a)
fig. (f)
fig. (e)
fig. (g)
fig. (g)
Y-Not Split-It Packa
g
e Contents
for JD type (per sin
g
le row)
Item
Quantity
“Y” . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1/4 Black Hose . . . . . . . . . . . . . . . . . . . 1
3/8” Clear Hose . . . . . . . . . . . . . . . . . . . 1
Metal Plate . . . . . . . . . . . . . . . . . . . . . . 1
12x3/8” Phillips Screws . . . . . . . . . . . . 2
L-Bracket . . . . . . . . . . . . . . . . . . . . . . . 1
Washer . . . . . . . . . . . . . . . . . . . . . . . . . 1
Propeller T-Nut . . . . . . . . . . . . . . . . . . . 1
Screw for T-Nut Slotted . . . . . . . . . . . . . 1
Instruction Sheet . . . . . . . . . . . . . . . . . 1
Y-Not Split-It Packa
g
e Contents
for IH 800/900 type (per sin
g
le row)
Item
Quantity
“Y” . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1/4 Black Hose . . . . . . . . . . . . . . . . . . . 1
3/8” Clear Hose . . . . . . . . . . . . . . . . . . . 1
Tie Strap . . . . . . . . . . . . . . . . . . . . . . . . 1
Metal Plate . . . . . . . . . . . . . . . . . . . . . . 1
12x3/8” Phillips Screws . . . . . . . . . . . . 2
Tube Clamp . . . . . . . . . . . . . . . . . . . . . . 1
Instruction Sheet . . . . . . . . . . . . . . . . . 1
Y-Not Split-It Packa
g
e Contents
for IH 1200 type (per sin
g
le row)
Item
Quantity
“Y” . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1/4 Black Hose . . . . . . . . . . . . . . . . . . . 1
3/8” Clear Hose . . . . . . . . . . . . . . . . . . . 1
Tie Strap . . . . . . . . . . . . . . . . . . . . . . . . 1
Metal Plate . . . . . . . . . . . . . . . . . . . . . . 1
12x3/8” Phillips Screws . . . . . . . . . . . . 2
Instruction Sheet . . . . . . . . . . . . . . . . . 1
JD type
Rebounder
Old style IH
(800/900/955)
Rebounder
New style
IH 1200
Rebounder
Y-Not Split-It Packa
g
e Contents
for
JD
type (per sin
g
le row)
Item Quantity
Clear “Y” . . . . . . . . . . . . . . . . . . . . . . . . 1
Yellow “Y” . . . . . . . . . . . . . . . . . . . . . . . 1
1/4" Gray Hose . . . . . . . . . . . . . . . . . . . 1
3/8" Clear Hose . . . . . . . . . . . . . . . . . . . 1
Metal Plate . . . . . . . . . . . . . . . . . . . . . . 1
12x3/8" Phillips Screws . . . . . . . . . . . . . 2
L-Bracket . . . . . . . . . . . . . . . . . . . . . . . 1
Washer . . . . . . . . . . . . . . . . . . . . . . . . . 1
Propeller T-Nut . . . . . . . . . . . . . . . . . . . 1
Screw for T-Nut Slotted . . . . . . . . . . . . . 1
Instruction Sheet . . . . . . . . . . . . . . . . . 1
Y-Not Split-It Packa
g
e Contents
for
IH 800/900
type (per sin
g
le row)
SEE BACK SIDE
Item Quantity
Clear “Y” . . . . . . . . . . . . . . . . . . . . . . . . 1
Yellow “Y” . . . . . . . . . . . . . . . . . . . . . . . 1
1/4" Black Hose . . . . . . . . . . . . . . . . . . . 1
3/8" Clear Hose . . . . . . . . . . . . . . . . . . . 1
Tie Strap . . . . . . . . . . . . . . . . . . . . . . . . 1
Metal Plate . . . . . . . . . . . . . . . . . . . . . . 1
12x3/8" Phillips Screws . . . . . . . . . . . . . 2
Tube Clamp . . . . . . . . . . . . . . . . . . . . . . 1
Instruction Sheet . . . . . . . . . . . . . . . . . 1
Y-Not Split-It Packa
g
e Contents
for
IH 1200
type (per sin
g
le row)
SEE BACK SIDE
Item Quantity
Clear “Y” . . . . . . . . . . . . . . . . . . . . . . . . 1
Yellow “Y” . . . . . . . . . . . . . . . . . . . . . . . 1
1/4" Black Hose . . . . . . . . . . . . . . . . . . . 1
3/8" Clear Hose . . . . . . . . . . . . . . . . . . . 1
Tie Strap . . . . . . . . . . . . . . . . . . . . . . . . 1
Metal Plate . . . . . . . . . . . . . . . . . . . . . . 1
12x3/8" Phillips Screws . . . . . . . . . . . . . 2
Instruction Sheet . . . . . . . . . . . . . . . . . 1
ATTENTION
Use the Yellow “Y” if you are applying less than 6 GPA .
They are half the size of the clear “Y” in the package .
Step #1:
Take the propeller t-nut
(fig. (a))
and insert it into the hole on the backside of the
Rebounder saw tooth insert
(fig.(b))
using a hammer or pliers to press it into the plastic.
Step #2:
Turn the saw tooth over, placing it into the Rebounder (see Rebounder mt. instructions for
proper placement of the saw tooth).Now place the L-bracket
(fig.(c))
with the small hole
on the Rebounder with the washer
(fig. (d))
on top, over the hole of the propeller t-nut.
Step #3:
Using a screw driver, tighten the round-head, slotted (10-24 x 3/8″) screw
(fig.(e))
into
the propeller t-nut.
Step #4:
Using a hair dryer on low or medium setting, briefly heat the short piece of clear hose.
Quickly push heated end of this hose all the way over the barbed end of the “Y”.
Step #5:
Install the clear hose and “Y” between the raised area that holds the screws. The “Y”
should bump up against the molded-in tab
(
fig. (g))
.
Step #6:
Place the metal plate over the clear hose and install the 2# 12 x 3/8″ Pan Phillips type
screw into the holes of the Rebounder.
Step #7: If you are putting “Y’s” on worn Rebounders:
after mounting the first
Rebounder with Y-Not, check to make sure that the outlets on the Y-Not do not extend
past the edge of the Rebounder. Trim with a side dike
(fig. (h))
. Clean out the holes with
a pocket knife after clipping; this will keep the Y-Not from plugging.
Step #8:
If you prefer to have the fertilizer closer to the bottom of the seed furrow you can cut the
molded-in tabs off
(fig. (i))
. Slide the Y-Not closer to the end of the Rebounder before
tightening the screws on the metal plate. Then refer to step 7. Normally this is only done
for inoculates. Refer to Hose Holder Instructions as it will do what cutting the tab off will
do.
Important Points to Remember:
-
Do not over-tighten or bottom out the screws into the Rebounders as this can damage
the plastic.
-
I
MPORTANT!! Do not strap any large tie around any part of the hose.
This 1/4″ hose must be able to flex with the Rebounder independently. House holder
kits are available for securing the hose.
