Schacht MIGHTY WOLF FL3002E Скачать руководство пользователя страница 4

- 4 -

MIGHTY WOLF PARTS

left and right pairs of legs

left and right castle sides

treadle assembly 

rear leg brace

cloth beam

front castle cross brace

front beam with front beam extension

left and right beater sides

beater race

beater top

jack assemblies—numbered on yellow stickers

4-shaft looms: 

2X #1 jack assemblies, 2X #3 jack 

assemblies

8-shaft looms: 

2X #1 jack assemblies, 2X #2 jack 

assemblies, 2X #3 jack assemblies,  

2X #4 jack assemblies

4 Now-4 Later looms: 

2X #1 jack assemblies,  

2X #2 jack assemblies

rear castle cross brace 

shaft frames and heddle bars: 

4-shaft looms: 

4X shaft frames, 8X heddle bars

8-shaft looms: 

8X shaft frames, 16X heddle bars

4 Now-4 Later looms: 

4X shaft frames, 8X heddle bars

2X 

upper castle supports 

tray bottom

warp beam

removable back beam

3X 

apron bars

2X 

lease sticks (with holes)

right pair of legs  

(inner side)

left pair of legs  

(inner side)

left and right beater sides 

(inner sides)

left and right castle side (inner side),  

 

8-shaft and 4 Now-4 Later looms 

left and right castle side (inner 

side), 4-shaft looms 

treadle assembly, 4-shaft looms

treadle assembly, 8-shaft and 4 Now-4 Later looms

Содержание MIGHTY WOLF FL3002E

















Отзывы: