www.scarlett.ru
SC-1160/61/62
4
GB
INSTRUCTION MANUAL
IMPORTANT SAFEGUARDS
·
Please read all instruction manuals before use and save it for future references.
·
Before first switching on check that voltage indicated on the rating label corresponds to the mains voltage in your home.
·
For home use only. Do not use for industrial purposes. Use the steam iron only for its intended use.
·
Do not use outdoors or in damp area.
·
Do not immerse the steam iron and cord in water or other liquids.
·
Never pull the cord while disconnecting from the power outlet; instead, grasp the plug only and pull to disconnect.
·
Do not allow the cord to touch sharp edges and hot surfaces.
·
Always unplug appliance from the power supply when not in use.
·
Do not operate the appliance with damaged cord or plug, or after the appliance malfunctions, or has been dropped or damaged in any
manner. To avoid the risk of electric shock, do not disassemble the steam iron; take it to a service center for examination, repair or
mechanical adjustment.
·
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning use of the appliances by a person
responsible for their safety
·
Children should be supervised to ensure that they do not play with the appliance.
·
Do not leave appliance unattended while operating.
·
The oil heater must be used only in the upright position.
·
Unit surface temperature of the appliance is high, thus do not touch it, except the handle.
·
Operating unit should be far away from the flammable or easy bulging under high temperature objects.
CAUTION:
·
To avoid a circuit overload, do not operate another high wattage appliance on the same circuit.
·
Do not cover the appliance when in use.
ASSEMBLING
·
Assemble wheel couples as shown at the picture.
·
Fasten them with two screws enclosed.
·
Fit wheels to the oil heater body.
USING THE APPLIANCE
·
Set thermostat to minimal position with power switch at
position, and then plug in the appliance.
POWER SELECTOR
·
You can adjust oil heater current power using power regulator:
Off;
Minimal power;
III
Maximum power.
THERMOSTAT
·
Set thermostat to maximum position.
·
When the temperature rises to satisfying level, slowly turn the thermostat counterclockwise until the indicator lights is out, and the room
temperature thus can keep constant.
·
If you want to change the room temperature, you can make another regulation: turn the thermostat clockwise to arise the temperature and
counterclockwise to lower it.
NOTES:
·
The room must be properly sealed, if not, using of oil heater will not make good result because of heat leakage.
·
After use, turn the power selector to the
0
position, then turn the thermostat to the
MIN
position and unplug from power supply.
CLEAN AND CARE
·
The oil heater should be cleaned regularly to wipe out the dust on the surface of fins. As this may result the radiating efficient.
·
Unplug from the power supply and allow the appliance to cool down.
·
Wipe out with a soft damp cloth. Do not use detergent or abrasives.
·
Do not scrap the surfaces of fins with sharp hard tools, to avoid surfaces getting rusty, because of damage of the paint coat.
STORAGE
·
Switch off and unplug the appliance. Ensure the oil heater is completely cool.
·
Complete all requirements of chapter CLEAN AND CARE.
·
Reel on the power cord.
·
Keep the appliance in a dry cool place.
RUS
·
.
,
.
·
,
,
,
.
·
.
.
·
.
·
.
·
,
.
·
,
.
·
,
.
·
.
.
·
,
.
,
.
·
.
·
.
·
.
·
,
.
·
.
