RTC
®
5 PC Interface Board
Rev. 1.9 e
7 Basic Functions for Scan Head and Laser Control
122
innovators for industry
Activating Image Field Correction
To activate image field correction, the appropriate
correction tables must be loaded (via
) from the corresponding
correction files into RTC
®
5 memory at the beginning
of an application and subsequently assigned (via
) to the
scan head connectors used by the application (see
the following sections).
2D correction tables will activate an image field
correction for X and Y coordinates, 3D correction
tables (if the 3D option is enabled, see below) addi-
tionally for Z coordinates.
2D and 3D Correction Files
SCANLAB calculates 2D and 3D correction tables and
supplies them in 2D and 3D correction files. RTC
®
5
correction files use the extension
.ct5
and the
following naming scheme:
•
D2_xxx.ct5
for 2D correction files
•
D3_yyy.ct5
for 3D correction files
Here,
xxx
and
yyy
are numbers. Each correction file is
calculated for a specific optical configuration. The
configuration is specified in the accompanying
Readme.txt file and in parameters of the correction
file’s header (also see
"Correction File Header", page
).
Loading Correction Tables
Up to four correction tables can be loaded from the
corresponding correction files into RTC
®
5 memory
via
).
If the 3D option is
not
enabled, then only 2D
correction tables can be loaded. They can be loaded
from 2D or 3D correction files (3D correction files also
contain 2D correction tables; if desired, the 3D data
sections are simply ignored). In this way, 3D
correction files are also usable for 2D scan systems.
If the 3D option
is
enabled, then 3D correction tables
can also be loaded (even in a mix with 2D correction
tables). A 3D correction table can also be loaded from
a 2D correction file. The 2D correction table will be
thereby automatically expanded to incorporate a
linear Z correction. The actually suitable Z correction
can subsequently be loaded via the
).
Assigning Loaded Correction Tables
Loaded correction tables are assigned to the two scan
head control ports via
If neither the “second scan head control” option nor
the 3D option is enabled, then a 2D correction table
(one of the possibly four loaded correction tables)
can be assigned (only) to the primary scan head
connector.
If the “second scan head control” option (but not the
3D option) is enabled, then a 2D correction table can
be assigned to the two scan head control ports each.
Then the secondary scan head connector outputs the
same signal types as the primary scan head
connector. Selectively, the same or two different
correction tables can be assigned to the two scan
head control ports.
If the 3D option (but not the “second scan head
control” option) is enabled, then a 2D or 3D
correction table can be assigned (only) to the primary
scan head connector. If a 2D correction table is
assigned, then the primary scan head connector
outputs signals for an XY scan system. If a 3D
correction table is assigned, then the RTC
®
5 addi-
tionally outputs signals for the third axis (Z axis) via
both channels of the secondary scan head connector.
If
both
options (“second scan head control”
and
3D
option) are enabled, two (different) 2D correction
tables can then be assigned to the two scan head
control ports. But it is not possible to simultaneously
assign two 3D correction tables.
Nor
is it possible to
simultaneously assign a 2D and a 3D correction table.
For controlling a 3D system, exactly one of the two
connectors must be assigned a 3D correction table.
Signals can then be outputted via this scan head
connector to an XY scan head – and via both channels
of the other scan head connector to the third axis (Z
axis). When assigning the correction table, the user
specifies which signals (XY or Z) are to be outputted
via which connector.
