Scania OC16 Скачать руководство пользователя страница 20

Страница: 20 / 73

OPM 320 en-GB

Scania CV AB 2019, Sweden

Maintenance

Maintenance

The maintenance programme covers a number of

points that are divided into the following sec-

tions:

• Lubrication system.
• Air cleaner.
• Cooling system.
• Fuel system.
• Electrical system.
• Miscellaneous.

WARNING!

Block the starting device and switch off the man-

ual fuel cock when working on the engine. If the

engine starts unexpectedly, there is a serious risk

of injury.

There is always a risk of sustaining burns when

an engine is hot. Particularly hot parts are turbo-

chargers, oil sumps, hot coolant and oil in pipes

and hoses.

The maintenance programme includes the fol-

lowing:

• R maintenance: One event when taken into

service.

• S maintenance: Minimum basic maintenance.
• M maintenance: More extensive mainte-

nance.

• L maintenance: Includes nearly all mainte-

nance items in the form.

• XL maintenance: Includes all maintenance

items in the form.

During a period, the sequence is S-M-S-L-S-M-

S-L-S-M-S-XL.

6000

5500

5000

4500

4000

3500

3000

2500

2000

1500

1000

500

3 153

IMPORTANT!

On delivery a Scania engine is optimised for its

application. However, regular maintenance is

necessary to

• prevent unplanned stops
• extend the service life of the engine
• maximise the long-term emission perfor-

mance of the engine

• give the best possible operating economy.

Содержание OC16










































































Результаты поиска

Содержание OC16

Отзывы:

Похожие инструкции для OC16

Бренды по названию

Популярные бренды

Scania OC16, Руководство оператора

Результаты поиска

Содержание OC16

Отзывы:

Похожие инструкции для OC16

Бренды по названию

Популярные бренды