![background image](http://html1.mh-extra.com/html/scandomestic/dks-142/dks-142_user-manual_1206461007.webp)
REVERSING THE DOOR H
I
NGE
The door can be opened from left to right and vice versa. Should
you wish to change the opening direction, please follow these in-
structions.
Note: all parts removed should be kept safely. You will require
these for the reinstallation of the door.
• Remove the two screws (1) that hold the upper hinge
(5)(right side) to the frame.
• Lift the door off and place on a padded surface to prevent
scratching.
• Remove the blanking plug (8) from the hole in the upper left
corner of the door and transfer it to the uncovered hole on
the upper right corner. Press firmly to secure it.
• Remove the two screws (6) that hold the lower hinge (2)
• Remove the adjustable front left foot and transfer it to the
other side.
• Remove the bolt pin(7) from the lower hinge (2) and reverse
the direction of the lower hinge. Secure the lower hinge (2)
to the left side of the lower frame with the two screws (6)
Re-insert the bolt pin (7). Set the door into position, making
sure it is seated comfortably onto the lower hinge (2).
• Holding the door closed, secure the upper hinge (5) into the
top frame with the two screws (1). Check the door is level
and tighten the screws firmly.
Fig 1 Position of components prior to reversal of the door hinge.
Fig 2 Position of components after reversal of the door hinge.
BEFORE USING FOR THE FIRST TIME
• The appliance may be placed with its rear panel at a distance
of at least 10 cm away from the wall to allow air circulation.
• Your Cooler should be placed on flat and firm surface for
quieter operation.
• Do not expose the appliance to direct sunlight or a heat
source such as ovens, radiators, heaters, etc.
• Do not under any circumstances place heated beverages in
your Cooler.
• Do not open the door more often than necessary to lessen
the escape of cold air.
• For better air circulation, do not overfill the unit.
• Adjust the temperature regulator according to the amount
of product and the ambient temperature.
BASIC OPERATION
Your Cooler must stand on an even surface. If the appliance is to
be placed on carpet or delicate floors, support it with a wooden
board underneath. Be aware that placing the appliance on carpet
may mean that heat from the compressor may cause the carpet
to fade. Be aware that humidity can cause water damage.
1. Clean the inner compartment.
2. Plug in your Cooler.
3. The first time you turn the unit on, set the thermostat, situ-
ated at the back of the unit, to the max. position “5”.
4. After 20 minutes, adjust the temperature control setting to
“3”. This setting should be correct for home use.
5. To turn the unit off, disconnect the plug from the mains
supply.
NOTE:
If the unit is unplugged or power lost, you must wait 3
to 5 minutes before restarting. If you attempt to restart the
unit before this delay, the unit will not start.
ADJUST OPERATING TEMPERATURE
1. Press and hold to turn the Power ON and OFF
2. Press and hold (1) and (3) simultaneously to Unlock and Lock
the Control Panel
3. Turns the Interior Light ON and OFF
4. Displays the Temperature
5. Increases Set Temperature 1°C with Each Push
6. Decreases Set Temperature 1°C with Each Push
7. Press and hold (5) and (6) simultaneously to Alter the
Temperature Display to Fahrenheit or Celsius.
WARNING
If temperature selector is set to too low a setting, drinks become
frozen. In extreme circumstances, glass bottles may even break.
Always exercise caution when setting the temperature.
• Do not place heavy items (more than 20kg) on top of the
Cooler.
• Do not place any items on top of the Cooler which may fall
off when the door is opened.
Please there are two options: 1. Wine Cooler mode and 2.
Beverage Cooler mode. Please push "+" and "LED" at the same
time for 6 seconds to switch between the two modes.