SCAN domestic IKF 360 Flex, Руководство пользователя, Страница: 15 / 23

15
If you do not have a magnet:
1 Put some water in the pan you want to check.
2 Follow the steps under ”To start cooking”.
3 If does not flash in the display and the water is heating, the
pan is suitable.
Cookware made from the following materials is not suitable:
Pure stainless steel, aluminium or copper without a magnetic
base, glass, wood, porcelain, ceramic, and earthenware.
• Do not use cookware with jagged edges or a curved base.
• Make sure that the base of your pan is smooth, sits flat
against the glass, and is the same size as the cooking zone.
Use pans whose diameter is as large as the graphic of the
zone selected. Using a pot a slightly wider energy will be
used at its maximum efficiency. If you use smaller pot ef-
ficiency could be less than expected.
• Pot less than 140 mm could be undetected by the hob.
Always centre your pan on the cooking zone.
• Always lift pans off the Induction hob – do not slide, or they
may scratch the glass.
Using your Induction Hob
To start cooking
1. Touch the
”ON/OFF” control.
After power on, the buzzer beeps once, timer control show
“00“ heating zone selection controls show one of the fol-
lowing symbols and indicating that
the induction hob has entered the
state of standby mode.
2 Place a suitable pan on the cooking zone that you wish to
use.
Make sure the bottom of the pan and the surface of the
cooking zone are clean and dry.
3 Touching the heating zone selection control, and a indicator
where you touched will flash
4 Adjust heat setting by touching the slider control.
If you don’t choose a heat setting within 1 minute, the Indu-
ction hob will automatically switch off. You will need to start
again at step 1.
You can modify the heat setting at any time during cooking.
If the display flashes alternately with the heat setting this
means that:
- you have not placed a pan on the correct cooking zone or,
- the pan you’re using is not suitable for induction cooking or,
- the pan is too small or not properly centred on the cooking
zone.
No heating takes place unless there is a suitable pan on the cook-
ing zone.
The display will automatically turn off after 1 minute if no suit-
able pan is placed on it.
When you have finished cooking
1 Touching the heating zone selection control that you wish to
switch off
2 Turn the cooking zone off by touching the slider to the left.
Make sure the display shows ”0”
3 Turn the whole cooktop off by touching the ON/OFF control.
Beware of hot surfaces
”H” will show which cooking zone is hot to touch. It will disap-
pear when the surface has cooled down to a safe temperature. It
can also be used as an energy saving function if you want to heat
further pans, use the hotplate that is still hot.
Using the Boost function
Actived the boost function
1 Touching the heating zone selection control
2 Touching the boost control, the zone indicator show “b” and
the power reach Max.
Cancel the Boost function
1 Touching the heating zone selection control that you wish to
cancel the boost function
2 A: Touching the boost control “b”, then the cooking zone
will revert to its original setting.
B: Touching the slider control, then the cooking zone will
revert to the level you select.
OR
• The function can work in all cooking zones
• The cooking zone returns to its original setting after 5 mi-
nutes.
• As the boost function of 1st cooking zone is activated ,the
2nd cooking zone is limited under level 2 automatically. vice
versa
• If the original heat setting equals 0, it will return to 9 after 5
minutes.
Using the Keep Warm function
Actived the Keep warm function
1 Touching the heating zone selection control
2 Touching the ”keep warm” control, the zone indicator show
“ ’ “ Cancel the ”keep warm” function.
1 A: Touching the ”keep warm” control, then the cooking
zone will revert to its original setting.
A: Touching the slider control, then the cooking zone will
revert to the level you select.
5 4
2 2 1 3
7 6