The memory function
The SC 6400 can store up to 85
measurements in the memory area.
Together
with
each
measurement
(systolic, diastolic and heart rate), the
date and time are also saved. The
measurement with the longest residence
time in the memory is assigned number
1. All other measurements increment by
one until number 85. Then the memory is
full. The next measurement occupies
memory location 85. The measurement
formerly at location 85 changes to
location 84 (etc., 83
82 .... 2
1). The
oldest measurement formerly at location
1 is lost.
Memory recall
With the MEMORY button you can recall
the memories.
Delete a blood pressure value from the
memory
Press the MEMORY button to view the
blood pressure value you want to delete.
Pressing the 0/I-START button instantly
(and holding it for at least 4 secs.)
displays:
dEL (for "delete") and the number of
the memory location.
Press the 0/I-START button instantly and
the value will be deleted.
Delete all blood pressure values in the
memory
Press the MEMORY button to display any
blood pressure value. Pressing the
POWRER key instantly (and holding it for
at least 4 secs.) displays:
dEL (for "delete") and the number of
the memory location
Press the MEMORY button instantly and
the LCD displays:
dEL (for "delete") and ALL (for all
memory locations).
Press the 0/I-START button instantly and
- 6 -
all values will be deleted. Time and date
are not deleted.
WHO*-Interpretation of blood pressure
readings
29.12.2007
Meaning
Systolic /
mmHg
Diastolic /
mmHg
optimal
< 120
< 80
normal
< 130
< 85
high-normal
130 - 139
85 - 89
mildy
hypertonic
140 - 159
90 - 99
hypertonic,
medium
severity
160 - 179
100 - 109
severly
hypertonic
> 180
> 110
The World Health Organization (WHO)
recommends medical treatment, when
the blood pressure value exceeds 140/90
mmHg.
Examples:
Cleaning and maintenance
♥
Do not expose the BP monitor to
extreme temperature, moisture, dust or
direct sunlight.
♥
The cuff contains a sensitive airtight
bulb. Treat it with care and avoid any
stress by torsion or kinking.
♥
Clean the BP monitor with a soft, dry
cloth. Do not use fuel, thinner or other
solvent. Remove specks on the cuff
carefully with a wet cloth and soap water.
Do not wash the cuff.
♥
Do not drop the BP monitor or treat it
with force.
- 7 -
♥
Do not try to open the BP monitor. This
will make the factory calibration invalid
Troubleshooting and remedies
If
a
fault
is
detected
during
a
measurement, the BM monitor displays
„Err“ and a symbol (code for service
personnel).
From many years of experience we know
that most faults are the consequence of
wrong use. The most frequent causes of
faults are excessive movement during the
measurement, wrong application of the
cuff, use of wrong batteries or use of a
rechargeable battery.
Message
Error description
Correction
The pressure
measured was
lower than
20mmHg.
Please measure
again.
The pressure
measured was
higher than
300mmHg.
Please measure
again.
Pumping error.
Please check cuff
and try again.
The pressure can
not be measured
due to signal
noise.
Please measure
again.
The pumping
pressure is
higher than
300mmHg.
Please measure
again.
or no
display
Low batteries.
Please check and
replace the batteries
if necessary.
Wait at least 5 minutes before repeating
the measurement.
Periodic re-calibration
We recommend periodic checks of the
pressure indication every 2 years.
Referenced norms
For registration, a defined number of
blood pressure monitors was subjected to
stringent clinical testing. These monitors
- 8 -
used the same program for blood
pressure measurement as your monitor
uses. Thus, this program is also regarded
as clinically tested.
The manufacture of the blood pressure
monitor complies with the European
norms for blood pressure monitors: EN
60601-1, EN 1060-1 to EN 1060-3.
Electromagnetic compatibility:
The blood pressure monitor complies with
the requirements of European norm EN
60601-1-2.
The
requirements
of
EU
directive
93/42/EEC concerning medical devices,
class IIa are complied with.
Warranty
We grant a warranty of two years for the
blood pressure monitor SC 6400. Within
this period, defects of the BP monitor will
be repaired free of charge. You can also
have your BP monitor repaired by our
customer service after the warranty
period. We will provide you with a free
cost estimate for the repair.
The warranty does not cover damage due
to improper handling, accident, natural
wear and tear (cuff), non-compliance with
the instructions for use or unauthorized
modifications of the monitor.
Excluded from the warranty are:
the
packaging,
batteries
and
the
instructions for use.
Disposal note
The disposal of batteries is regulated.
Spent batteries are collected at collection
points provided by battery dealers and
the communities.
Dispose of the blood pressure monitor as
prescribed. i.e., at a collection point for
electrical scrap.
- 9 -
Specifications
Measuring method: Oscillometric
Measuring range: Pressure: 20 to 300mmHg
Heart rate: 40 to 200/min
Measuring accuracy: stat. pressure: +/- 3mmHg
Heart rate: +/- 5 %
Measuring value memory:
memory with 85 locations
for systolic / diastolic /
heart rate, date and time
Display: LC display
Automatic switch-off:
after approx. 1 minute of
inactivity
Voltage supply:
2 x LR03 (alkali batteries),
Working temperature range:
+10°C - +40°C
Storage temperature range:
- 10°C - +50°C
Weight (without batteries): approx. 100 g
Cuff length:
for wrist circumference
from 135mm to 195mm
Specifications may change as technical
improvements take place
*WHO – World Health Organization
Service client
SCALA Electronic GmbH SES GmbH
Ruhlsdorfer Str.95
Ruhlsdorfer Straße 95
14532 Stahnsdorf 14532 Stahnsdorf
Explanation of symbols
Rev. 25/07/2012/GB
- 10 -
