background image

22

R

Section 6

PARkING BRAkE ADJUSTMENT

6.1 

 WARNING

Do  not  operate  the  mower  if  the  parking  brake 
is  not  operable.  Possible  severe  injury  could 
result. 

The parking brake linkage should be adjusted whenever 
the parking brake lever is placed in the “ENGAGE” position 
and the parking brake will allow the mower to move. If the 
following procedures do not allow you to engage the parking 
brake properly, contact your Scag dealer for further brake 
adjustments.

Position a floor jack under the rear of the machine. 

1. 

Raise the machine and support it to prevent it 
from falling. Block the caster wheels to prevent the 
machine from moving. Remove the drive wheels.

With the brake in the engaged position, check 

2. 

the distance between the lower nut on the brake 
actuator rod and the brake actuator lever on the LH 
side of the machine. The distance should be 1/8". 
See Figure 6-2.

If the distance is not at the specified measurement, 

3. 

loosen the jam nut at the clevis on the top of the 
brake actuator rod. See Figure 6-2.

Turn the bolt at the bottom of the brake actuator lever 

4. 

until the 1/8" measurement is achieved and tighten 
the jam nut at the clevis on the brake actuator rod. 
See Figure 6-2. If the 1/8" measurement can not 
be achieved by adjusting the brake actuator rod, 
adjust the brake control rod. Adjust by loosening the 
jam nuts at both ends of the brake control rod and 
turning the rod until the proper distance is achieved. 
See Figure 6-1.

Repeat steps 2-4 on the RH side of the machine.

5. 

Replace the drive wheels and test the brake.

6. 

- Note -

If this procedure does not achieve proper brake 
adjustment, please contact your authorized Scag 
dealer.

ADJUSTMENTS

LOOSEN
HERE

STC2002BA

BRAKE
HANDLE

Brake Adjustment

Figure 6-1. 

LOOSEN HERE

1/8"

390S0153-1

Brake Rod Adjustment

Figure 6-2. 

TRAvEL ADJUSTMENTS

6.2 

Neutral or tracking adjustments will need to be made if:

A.  The  steering  control  levers  are  in  the  neutral 
position and the machine creeps forward or backward. 
(Neutral Adjustment, See Page 23).

B.  The steering control levers are in the full forward 
position  and  the  mower  pulls  to  one  side  or  the 
other when traveling in a forward direction. (Tracking 
Adjustment, See Page 23).

Содержание Tiger Cat STC48V-25CV
















































































Отзывы: