manualshive.com logo in svg

Scag Power Equipment SWZT36-14FS, Руководство оператора

Поделиться
Скачать
Scag Power Equipment SWZT36-14FS Скачать руководство пользователя страница 12

8

R

Section 3

SPECIFICATIONS

ENGINE

3.1 

General Type ................................................................................................Heavy Duty Industrial/Commercial Gasoline
Brand ..................................................................................................................................................................Kawasaki
Engine Model:

(Scag Model SWZT36-14FS) ............................................................................................ Kawasaki Model # FS481V 
(Scag Model SWZT48-15FS) ............................................................................................ Kawasaki Model # FS541V
(Scag Model SWZT52-18FS) ............................................................................................ Kawasaki Model # FS600V 
(Scag Model SWZT52-18FSE) .......................................................................................... Kawasaki Model # FS600V 
(Scag Model SWZT61-22FSE) .......................................................................................... Kawasaki Model # FS651V

Displacement:

Kawasaki FS481V .............................................................................................................................................. 603cc
Kawasaki FS541V .............................................................................................................................................. 603cc
Kawasaki FS600V .............................................................................................................................................. 603cc
Kawasaki FS651V .............................................................................................................................................. 726cc

Cylinders ...................................................................................................................2 with Cast-Iron Sleeves - Kawasaki
Governor ................................................Mechanical Type with Variable Speed Control Set At 3600 RPM (+/- 100 RPM)
Idle Speed:

Kawasaki ............................................................................................................................. 1550 RPM (+/- 150 RPM)

Fuel ...................................................................................... Non-Leaded Gasoline with a Minimum Octane Rating of 87
Oil Pump ...............................................................................................varies - see engine manufacturer's specifications
Starter:

Kawasaki .................................................................................................................................. Recoil or Electric Start

ELECTRICAL

3.2 

Starter ...................................................................................................................... Electrical Ignition with Recoil Starter
Interlock Switches ................................................Operator Presence, Mower Engagement (BBC), Transmission Neutral
Instrument Panel .................................................... Key Switch, Throttle Lever, Choke Control, PTO Switch, Hour Meter

ENGINE DECk

3.3 

Drive System ......................................................... Hydraulic Drive with Two  Hydro-Gear™ Integraded Zero-Turn Axles

Model ........................................................................................................................................Hydro-Gear™ ZT-2800

Steering/Travel Control ..........................................Independent Handle Controls for each wheel, squeeze to move from
 

forward to neutral to reverse, neutral lock lever, speed range controlled

 

with single lever (patented design)

Parking Brake ...................................................................Lever Actuated Linkage to Brakes on Both Drive Wheel Axles
Wheels:

(2) Front Caster .............................................................................  9 X 3.5-4 Pneumatic Tubeless, w/Roller Bearings
(2) Drive -  .............................  18 x 6.5-8 (36) or 18 x 8.5-8 (48, 52, 61) Four-Ply Pneumatic Tubeless, Radius Edge

Tire Pressure:

Front Caster....................................................................................................................................................Flat Free
Drive .................................................................................................................................................................. 12 PSI

Fuel Tank .................................................. 5-1/2 Gallon Seamless Polyethylene Tank with Large Opening and Fuel Cap
Travel Speed:

Forward ................................................................................................................................................. 0 up to 7 MPH
Reverse ................................................................................................................................................. 0 up to 3 MPH
-NOTE- The machine will travel at 7 mph for transport purposes. For best cutting performance the forward travel 
speed should be adjusted depending upon the cutting conditions.

Содержание SWZT36-14FS




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды