Scag Power Equipment STT-29CH-EFI Скачать руководство пользователя

Страница: 35 / 95

Section 6

C.  4-3/4" or 5-1/4" Position - (See Figure 6-9). Placing
the  baffle  in  either  the  4-3/4"  or  5-1/4"  setting  will
enhance  fall  cutting  (leaf  pickup)  and  reduce  cutter
deck "blowout".

To adjust the Custom-Cut Baffle height:

Place the cutter deck in the transport position.

Remove the hardware securing the Custom-Cut

Baffle to the cutter deck.

- NOTe -

Hardware location used in the illustrations are for
reference only. Location of hardware may vary
depending on cutter deck size.

Move the Custom-Cut Baffle to desired position. See

Figure 6-9.

Reinstall the mounting hardware. Torque hardware to

39 lb-ft.

1 2

3 4

Custom-Cut Baffle Adjustment

Mounting Slot Selected

Mounting Hardware Location

Slot “A”

Hole 1

Hole 2

Hole 3

Hole 4

Height (inches)

3-3/4”

4-1/4”

4-3/4”

5-1/4”

Slot “B”

Hole 2

Hole 3

Hole 4

Height (inches)

3-1/2”

4”

4-1/2”

7-Position Custom-Cut Baffle Adjustment

Figure 6-9.

Содержание STT-29CH-EFI
































































































Результаты поиска

Содержание STT-29CH-EFI

Отзывы:

Похожие инструкции для STT-29CH-EFI

Бренды по названию

Популярные бренды

Scag Power Equipment STT-29CH-EFI, Руководство оператора

Результаты поиска

Содержание STT-29CH-EFI

Отзывы:

Похожие инструкции для STT-29CH-EFI

Бренды по названию

Популярные бренды