background image

1

SIGNAL WORDS

This symbol means 

“Attention! Become Alert!

Your Safety is Involved!" 

  The symbol is used

with the following signal words to attract your

attention to safety messages found on the decals and

throughout this manual.  The message that follows

the symbol contains important information about

safety.  To avoid injury and possible death, carefully

read the message!   Be sure to fully understand the

causes of possible injury or death.

Signal Word:

It is a distinctive word on safety decals and through-

out this manual that alerts the viewer to the exist-

ence and relative degree of the hazard.

The signal word “DANGER” denotes that an ex-

tremely hazardous situation exists on or near the

machine that could result in high probability of

death or irreparable injury if proper precautions are

not taken.

The signal word “WARNING” denotes that a hazard

exists on or near the machine that can result in

injury or death if proper precautions are not taken.

The signal word “CAUTION” is a reminder of

safety practices on or near the machine that could

result in personal injury if proper precautions are not

taken.

INTRODUCTION

Your mower was built to the highest standards in the

industry. However, the prolonged life and maximum

efficiency of your mower depends on you following

the operating, maintenance and adjustment instruc-

tions in this manual.

We encourage you to contact your dealer for repairs.

All Scag dealers are informed of the latest methods

to service this equipment and provide prompt and

efficient service in the field or at their service shop.

They carry a full line of Scag service parts.

A replacement Operator's Manual is available from

your Scag Servicing Dealer or by contacting Scag

Power Equipment, Service Department at P.O. Box

152, Mayville, WI 53050.  Please indicate the com-
plete model and serial number of your Scag product.

USE OF OTHER THAN ORIGINAL SCAG

REPLACEMENT PARTS WILL VOID THE

WARRANTY.

The “Right” and “Left”, “Front” and “Rear” of the

machine are referenced from the operator’s perspec-

tive when in the normal operating position and

facing the forward travel direction.

GENERAL SAFETY INSTRUCTIONS

READ THIS OPERATOR'S MANUAL

 and all

instructions furnished with attachments.

Perform only those maintenance procedures de-

scribed in this manual. If major repairs are ever

needed or assistance is desired, contact an Author-

ized Scag Dealer. To ensure optimum performance

and safety, always purchase genuine SCAG replace-

ment parts and accessories.

Your safety and the safety of others depends signifi-

cantly upon your knowledge and understanding of

all correct operating practices and procedures of this

machine.

WARNING:

CAUTION:

Содержание STHM







































Отзывы: