background image

1

R

Section 1

INTRODUCTION

1.1 

Your  mower  was  built  to  the  highest  standards  in  the 
industry.  However,  the  prolonged  life  and  maximum 
efficiency  of  your  mower  depends  on  you  following  the 
operating,  maintenance  and  adjustment  instructions  in 
this manual.

If additional information or service is needed, contact your 
Scag Power Equipment Dealer.

We encourage you to contact your dealer for repairs. All 
Scag dealers are informed of the latest methods to service 
this equipment and provide prompt and efficient service in 
the field or at their service shop. They carry a full line of 
Scag service parts.

THE REPLACEMENT OF ANY PART ON THIS PRODUCT 
BY OTHER THAN THE MANUFACTURER'S AUTHORIzED 
REPLACEMENT PART MAY ADvERSELY AFFECT THE 
PERFORMANCE,  DURABILITY  OR  SAFETY  OF THIS 
PRODUCT.

USE OF OTHER  THAN ORIGINAL SCAG REPLACEMENT 
PARTS WILL vOID THE WARRANTY.

When  ordering  parts,  always  give  the  model  and  serial 
number of your mower. The serial number plate is located 
where shown in Figure 1-1.

SERIAL NUMBER
PLATE LOCATION

2012 SFZ SPL

Mower Serial Number Plate Location

Figure 1-1. 

GENERAL INFORMATION

USE ONLY SCAG APPROvED ATTACHMENTS AND 
ACCESSORIES.

Attachments and accessories manufactured by companies 
other than Scag Power Equipment are not approved for use 
on this machine. See Section 8, Paragraph 8-1.

 WARNING

For pictorial clarity, some illustrations and figures 
in this manual may show shields, guards or plates 
open or removed. Under no circumstances should 
your mower be operated without these devices 
in place.

All information is based upon product information available 
at the time of approval for printing. Scag Power Equipment 
reserves the right to make changes at any time without 
notice and without incurring any obligation.

DIRECTION REFERENCE

1.2 

The “Right” and “Left”, “Front” and “Rear” of the machine are 
referenced from the operator’s right and left when seated 
in  the  normal  operating  position  and  facing  the  forward 
travel direction.

SERvICING THE ENGINE AND DRIvE 

1.3 
TRAIN COMPONENTS

The  detail  servicing  and  repair  of  the  engine,  hydraulic 
pumps  and  gearboxes  are  not  covered  in  this  manual; 
only routine maintenance and general service instructions 
are  provided.  For  service  of  these  components  during 
the limited warranty period, it is important to contact your 
Scag dealer or find a local authorized servicing agent of 
the component manufacturer. Any unauthorized work done 
on these components during the warranty period may void 
your warranty.

Содержание SFZ61-30BS


































































Отзывы: