background image

 

 

IP-OPTODA16CH4 

4 channels of optically isolated 

16-bit D/Aconversion 

 

SBS Technologies, Inc.  

1284 Corporate Center Drive 

St. Paul, MN 55121-1245 

Tel: (651) 905-4700 

FAX: (651) 905-4701 

Email: [email protected] 

http://www.sbs.com

 

 

 

©2003 SBS Technologies, Inc. 
IndustryPack is a registered trademark of SBS 
Technologies, Inc.  QuickPack, SDpacK and Unilin are 
trademarks SBS Technologies, Inc.  PC

MIP is a 

trademark of SBS Technologies, Inc. and MEN Mikro 
GmbH. 

SBS Technologies, Inc acknowledges the trademarks of 
other organizations for their respective products 
mentioned in this document. 
 
All rights are reserved: No one is permitted to reproduce 
or duplicate, in any form, the whole or part of this 
document without the express consent of SBS 
Technologies, Inc. This document is meant solely for the 
purpose in which it was delivered. 
 
SBS Technologies, Inc. reserves the right to make any 
changes in the devices or device specifications contained 
herein at any time and without notice. Customers are 
advised to verify all information contained in this 
document. 
 
The electronic equipment described herein generates, 
uses and may radiate radio frequency energy, which can 
cause radio interference. SBS Technologies, Inc. 
assumes no liability for any damages caused by such 
interference. 
 
SBS Technologies, Inc.’s products are 

not

 authorized for 

use as critical components in medical applications such 
as life support equipment, without the express consent of 
the president of SBS Technologies, Inc., Commercial 
Group. 
 
This product has been designed to operate with 
IndustryPack, PC

MIP or PMC modules or carriers and 

compatible user-provided equipment. Connection of 
incompatible hardware is likely to cause serious damage. 
SBS Technologies, Inc. assumes no liability for any 
damages caused by such incompatibility. 
 

 

Содержание IP-OPTODA16CH4

















Отзывы: