Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and
satisfactory operation of this product. Please retain these instructions for future reference.
Warning
This is a Class 1 product and must be earthed.
Please read these instructions carefully before
commencing any work.
This unit must be fitted by a competent and qualified
electrician.
Install in accordance with IEE Wiring regulations and
current Building Regulations.
To prevent electrocution switch off at mains supply
before installing or maintaining this fitting. Ensure
other persons cannot
restore the electrical supply
without your knowledge. If you are in any doubt,
please consult a qualified electrician.
This light fitting should be connected to a circuit with a
30mA RCD fitted.
If replacing an existing fitting, make a careful note of
the connections.
The unit cannot be dimmed.
This system contains non-replaceable parts and
cannot be serviced. If damage occurs the part should
be scrapped.
Waste electrical products should not be disposed of
with household waste. Please recycle where facilities
exist. Check with your local authority or retailer for
recycling advice.
This product is not suitable for location in or near a
marine environment.
The entire unit gets hot whilst on for a period of time.
Terminal block not included.
Installation may require
advice from a qualified person.
Specification
Voltage:
240V
~ 50Hz
Lamp:
10W LED Module - IP65
73452:
73451:
10W LED Module - IP44
73453: 10W LED Module - IP65
73454: 10W LED Module - IP44
73455: 30W LED Module - IP65
73456: 30W LED Module - IP44
73457: 30W LED Module - IP65
73458: 30W LED Module - IP44
73459: 50W LED Module - IP65
73460: 50W LED Module - IP44
73461: 50W LED Module - IP65
73462: 50W LED Module - IP44
Layout
• Plan the desired layout of this fitting carefully,
ensuring the cables will reach the distance between
the junction box and the light fitting.
• Avoid locating any cables in positions that would
cause a hazard. Position cables and outdoor rated
junction boxes (not supplied) away from areas
where they may be at risk from being cut, trapped or
damaged.
• This product is supplied with 1.5 metres of H05RN-F
outdoor grade rubber sheathed cable - ready for
connection to an approved, outdoor rated terminal
block which is not supplied and must be obtained.
• Cables must be protected using suitable conduit or
plastic trunking.
• This is a floodlight product, and therefore should be
positioned where it will not cause a glare hazard.
Existing fittings must be completely removed before
installation of a new product. Before removing the
existing fitting,
carefully note the position of each set
of wires
.
• Decide on the optimum location for the product. For
PIR versions, the optimum height is between 1.8-
2.5m
• Hold the product in position and mark the location
of the fixing holes. A minimum of two fixing points
must be used. Ensure the wall is capable of holding
the weight of the product. The bracket can be
removed from the fitting for ease of installation
• Drill and plug the wall at the marked positions.
• Fix the bracket to the wall using the screws
provided and plugs. Take care to avoid damaging
any concealed wiring and pipes. The correct fixings
should be used for brick or cavity walls.
• Wire as detailed below.
Installation
NEUTRAL
EARTH
SWITCHED LIVE
BLUEN )
GREEN/YELLOW
BROWN (L)
SUPPLY
LIGHT FITTING
Terminal block not included.
Installation may require advice from a qualified person.
Connect to an approved
outdoor rated terminal block, observing the wiring diagram here:-
Wiring
Check that...
• You have correctly identified the wires.
• The connections are tight.
• No loose strands have been left out of the connection
block.
• Refit the cover on the IP terminal block. Ensure that
the seals are correctly located, and refit the screws.
• Using the supplied allen key, loosen the bolts on the
side, and adjust the fitting to the desired position.
Ensure that the cable is not snagged. Re-tighten the
bolts.
• Replace fuse or circuit breaker and switch on. Your
light is now ready for use.
Commissioning
