Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and
satisfactory operation of this product. Please retain these instructions for future reference.
Warning
This light fitting is Class 1 and must be connected to
an Earth circuit
Please read these instructions carefully before
commencing any work.
This unit must be fitted by a competent and qualified
electrician.
Install in accordance with IEE Wiring regulations and
current Building Regulations.
To prevent electrocution switch off at mains supply
before installing or maintaining this fitting. Ensure
other persons cannot restore the electrical supply
without your knowledge. If you are in any doubt,
please consult a qualified electrician.
This light fitting should be connected to a circuit with a
30mA RCD fitted.
If replacing an existing fitting, make a careful note of
the connections.
This system contains non-replaceable parts and
cannot be serviced. If damage occurs the part should
be scrapped.
Waste electrical products should not be disposed of
with household waste. Please recycle where facilities
exist. Check with your local authority or retailer for
recycling advice.
This product is rated at IP65.
This product is not suitable for dimming.
This product is not suitable for location in or near a
marine or sea environment.
Specification
Voltage:
240V 50Hz a.c.
Lamp: 68784: 2 x 1W LED Hi Power Natural White - 200lm
68785: 4 x 1W LED Hi Power Natural White - 400lm
IP rating:
65
Layout
Installation (if used as spike light)
• Plan the desired layout of this fitting carefully,
ensuring the cables will reach the distance between
the connector and the light fitting
• Avoid locating any cables in positions that would
cause a hazard. Position cables and junction boxes
(not supplied) away from areas where they may be
at risk from being cut, trapped or damaged
• Cables in walls must be protected using suitable
conduit or plastic trunking.
• The mains supply cable must have a minimum cross
sectional area of 1.0mm²
• This product has special protection against the
ingress of moisture and is IP65 rated.
• This product can be used as a spike light. If used
in this way, ensure that the ground is suitable
for pushing the spike into, and can support the
luminaire. Do not install in very wet or boggy areas.
Existing fittings must be completely removed before
installation of a new product. Before removing the
existing fitting,
carefully note the position of each set
of wires
.
• Wire as detailed below and screw the supplied spike
into the base of the product and place it into the
ground. (Fig. 1).
• Replace fuse or circuit breaker and switch on. Your
light is now ready for use.
Fig. 1
Installation (if used in concrete or decking)
Existing fittings must be completely removed before installation
of a new product. Before removing the existing fitting,
carefully
note the position of each set of wires
.
• Undo the 4 hexagonal screws with the supplied hex key
to detach the back ring plate from the product. Keep the
4 screws safe for refitting later. N.B once this ring plate is
removed, there is no need to disassemble the product further.
(Fig. 2)
• Place the back ring plate so the 4 fixing holes are flush with
the ground. Using the back ring plate as a template, mark the
position of the fixing holes. Drill the fixing holes. Take care
not to damage any concealed wiring or pipes.
• Fix the back ring plate into the ground using the supplied
expanding bolts. N.B. you may need to use a hammer to
gently tap the bolts into place to start with. Tighten the bolts
with a spanner to secure in place (Fig. 3).
• Wire as detailed below.
Fig. 2
Fig. 3
Wiring
• It is recommended that the Saxby IP68 inline
connector ref 61515 is used to wire this product.
Refer to layout diagram.
• Unscrew the threaded body at the centre of the
connector from both sides (Fig. 4a).
• Push the wires into the terminals, observing the
correct polarity (Fig. 4b). Make sure the gaskets
are in place to ensure ingress protection.
• Tighten the screws to secure in place (Fig. 4c).
• Refit the seals and locking nuts.
Fig.
4a
Fig.
4b
Fig.
4c
Layout
