SAW TRAX 2064 Скачать руководство пользователя страница 16

Страница: 16 / 19

15 |

P a g e

Loosen the bolts that attach the “hat” bracket to the aluminum

extrusion until you can slide them out of the groove & off the
extrusion.

Place the “hat” bracket over the vertical square tubing from the

backside of the frame. (as pictured)

c. Slide the aluminum extrusion back onto the bolts and line the

extrusion up with the end of the horizontal tubing closest to the
carriage.

Tighten bolts on the “hat” bracket till the extrusion no longer

moves.

e. Attach measuring tape on facing of the extrusion. (see

installation instructions-putting on horizontal tapes)

f. To set flips, loosen bolts on the flip stops. Slide to desired

placement & tighten. Push the arm bar down to use. When
not in use, push the arm bar up so material may slide pass the
stop.

Frame Dust collection

–

Secondary dust collection for the bottom frame of the

panel saw. This collects most of the dust before it
hits the floor.

a. Remove the pre-installed base plate located on the back of the

unit.

b. Attach the 4 inch coupler to the base plate using the bolts that

have been pre-inserted on the coupler. The coupler should be
attached on the flat side of the plate.

c. Re-attach the base plate to the back of the unit.
d. Attach a 4 inch hose to the coupler & to a dust collector. (hose

not provided)

e. NOTE: An industrial vacuum system is recommended for

effective dust collection.

ACM cutter

- Cuts Aluminum composite material, (such as Diabond &

Alumacore), expanded PVC, (Such as Sintra & Forex) without
dust.

This insert can only be inserted in a vertical position.

Place & secure your material so it will not move. Firmly hold

both handles and pull the insert down, completely through

the material. Remove your material so the insert may
retract without interfearence.

c. This insert is not capable of Rip cutting.

Knife Plate

– Used to cut softer material, such as, foam board, corrugated

PVC, Cardboard, & 4mm Coroplast.

Flip stops

Handles

Содержание 2064




















Результаты поиска

Содержание 2064

Отзывы:

Похожие инструкции для 2064

Бренды по названию

Популярные бренды

SAW TRAX 2064, Руководство пользователя

Результаты поиска

Содержание 2064

Отзывы:

Похожие инструкции для 2064

Бренды по названию

Популярные бренды