background image

11

15. TROUBLESHOOTING

Problem

Fan will not start.

Fan sounds 
noisy.

Remote control 
malfunction.

Fan wobble.

Solution

1. Check circuit fuses or breakers.
2. Check line wire connections to the fan and switch wire connections 

in the switch housing. 

CAUTION:

 Make sure main power is off.

3. Check to make sure the dip switches from the transmitter and 

receiver are set to the same frequency.

1. Make sure all motor housing screws are snug.
2. Make sure the screws that attach the fan blade bracket to the motor 

hub is tight.

3. Make sure wire nut connections are not rubbing against each other 

or the interior wall of the switch housing. 

CAUTION:

 Make sure main 

power is off.

4. Allow a 24-hour "breaking-in" period. Most noise associated with a 

new fan disappear during this time.

5. If using an optional light kit, make sure the screws securing the 

glassware are tight. Check that light bulb is also secure.

6. Do not connect the fan with wall mounted variable speed control (s).
7. Make sure the upper canopy is a short distance from the ceiling. It 

should not touch the ceiling.

1. Do not connect the fan with wall mounted variable speed control (s).
2. Make sure the dip switches are set correctly.

1.  Check that all blade and blade arm screws are secure.
2. Most fan wobbling problems are caused when blade levels are 

unequal. Check this level by selecting a point on the ceiling above the 
tip of one of the blades. Measure this distance. Rotate the fan until the 
next blade is positioned for measurement. Repeat for each blade. The 
distance deviation should be equal within 1/8".

3. Use the enclosed Blade Balancing Kit if the blade wobble is still 

noticeable.

4. If the blade wobble is still noticeable, interchanging two adjacent (side 

by side) blades can redistribute the weight and possibly result in 
smoother operation.

WARNING:

 To reduce the risk of personal injury, do not bend the blade 

arm while installing, balancing the blades, or cleaning the fan. Do not 
insert foreign objects between rotating fan blades.

Содержание 52-190-3CN-187













Отзывы: