Saveo Scan SAVEO-RV2-RCCD Скачать руководство пользователя страница 3

Страница: 3 / 140

There are two operating modes on the scanner,

Data transmis-

sion mode

and

Data Storage Mode

Scan the appropriate barcodes when switching between these

two modes.

Please note:

Switching between modes will wipe the scanner’s

internal memory.

Operating Modes

Data Transmission Mode (Default)

Our Default setting is Data Transmission mode. In this mode data

will be sent to smartphone/tablet directly.

To enter

Data Transmission Mode

please scan the follwing

barcodes.

Demo

%E%R%A

Demo

%M%A%F

Enter Data Transmission Mode

Green/Orange LED flashes followed by 3 beeps.

Demo

%M%A%N

Data Storage Mode

In this mode, data will be saved directly to scanner’s memory.
Scan

Transmit Memory Data

to receive data stored on scanner’s

internal memory.

Enter Data Storage Mode

Green/Orange LED flashes followed by 3 beeps.

Demo

%E%R%A

To enter

Data Storage Mode

please scan the follwing barcodes.

Demo

%E%R%A

Clean Memory Data

Green/Orange LED flashes

followed by 3 beeps.

Demo

%R%E%C

Transmit Memory Data

Green/Orange LED flashes

followed by 3 beeps.

Transmit Memory Data

Scan the following barcode to receive data stored in the

scanner’s internal memory..

After data is transmitted to your device it remains on the

scanner’s internal memory. Scan the following barcode to clear
the memory if you do not wish to send this data again

When the battery power is too low, the Orange LED will flash

and beep once.

Scanner should be charged immediately. If

scanner shuts down it is recommended to charge it fully then

power it back on.

Under power-saving mode, there will not be an LED

indication when charging.

Orange LED ON

Full charged

Orange LED (Flashing)

Charging / Low battery

Red LED ON

Offline / Out of Range

Green LED ON

Good read

Orange LED ON

Good read (Batch mode)

LED Indicator Information

LED Indicator

Reset to Defaults

Reset Configuration to Defaults

(scan from A1to A6)

HID Profile

Demo

W010F01

Demo

WFFD980

Demo

W100900

Demo

WFFD9C3

Demo

W010F00

Demo

%D%F%T

Demo

Current Battery Level

Scan to receive the current

battery level

Scan the following barcode to send battery level information

to your device. The format is outlined in the table below.

%^4^%

80% - 100%

%^3^%

55% - 80%

%^2^%

30% - 55%

%^1^%

10% - 30%

%^0^%

under 10%

Battery Level Status

Содержание SAVEO-RV2-RCCD













































































































































Результаты поиска

Содержание SAVEO-RV2-RCCD

Отзывы:

Похожие инструкции для SAVEO-RV2-RCCD

Бренды по названию

Популярные бренды

Saveo Scan SAVEO-RV2-RCCD, Руководство пользователя

Результаты поиска

Содержание SAVEO-RV2-RCCD

Отзывы:

Похожие инструкции для SAVEO-RV2-RCCD

Бренды по названию

Популярные бренды