PAV-VOMVP1F2-xx/PAV-VOMVP1CP2-xx QRG | 009-2059-00
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2022 Savant Systems, Inc | 220907
1 of 2
Savant.com | 508.683.2500
Savant IP Video Single Output Receiver 4K with POE+
(PAV-VOMVP1F2/ PAV-VOMVP1CP2)
Quick Reference Guide
Box Contents
(1) IP Video Receiver (PAV-VOMVP1CP2-xx/PAV-VOMVP1F2-xx)
(1) SFP+ module (PAV-VOMVP1F2-xx only)
(1) Installation Kit (075-0210-xx)
(1) Power Adapter with International Clips (025-0195-xx)
(1) International Clips (CN, US, UK, EU & AUS)
(2) Mounting Brackets (071-1093-xx)
(4) M2.5 x 4mm screws (for mounting brackets) (039-0590-xx)
(1) IR Emitter (4ft long) (064-0442-xx)
(1) 3-pin RS232 Control Connector (028-0805-xx)
(1) Product Regulatory Statement (009-1950-xx)
Specification
Environmental
Temperature
32° to 104° F (0° to 40° C)
Humidity
10% to 90% Relative Humidity (non-condensing)
Dimensions and Weights
Device
Shipping
Height
0.98 in (2.50 cm)
4.0 in (10.16 cm)
Width
8.46 in (21.50 cm)
9.0 in (22.86 cm)
Depth
5.51 in (13.99 cm)
16.0 in (40.64 cm)
Weight
1.65lb (0.75 kg)
4.8 lb (2.17 kg)
Power
Input Power
12V 2A DC
PoE+ (IEEE 802.3at)
Nominal Power
16 W (PAV-VOMVP1F2-xx)
19 W (PAV-VOMVP1CP2-xx)
Maximum Power
36 W
Compliance
Safety and
Emissions
FCC Part 15 CE
C-Tick
UKCA
RoHS
Compliant
Supported Release
Software Release da Vinci 9.4.3 and higher
Supported Audio and Video Formats
Audio
Supported
Formats
Pass-though of all HDMI audio formats are
supported.
Video
HDR
Supported
Dolby® Vision
Supported
Supported
Formats
640x480
5
1280x720
4
1920x1080
4
3840x2160
3
720x480
5
1280x720
5
1920x1080
5
3840x2160
4
720x576
4
1280x1024
5
1920x1080
5
3840x2160
5
800x600
5
1920x1080
1
3840x2160
1
4096x2160
3
1024x768
5
1920x1080
3
3840x2160
2
4096x2160
5
1 = @ 24 Hz
2 = @ 25 Hz
3 = @ 30 Hz
4 = @ 50 Hz
5 = @ 60 Hz
Required Components
–
Savant IP Video Transmitter
–
Savant System Host
–
Savant qualified 10G Managed Network Switch
–
Savant User Interface
–
Savant Development Environment (SDE) and Configuration Tools
Front Panel
System
G
USB HOST
H
I
P1
J
USB HID
Video
C
LinkTx
D
USB
F
LinkRx
E
Status
B
Power
A
Item
Description
A
Power LED
Off
- Device is off. No power applied.
Red
- Main board is powered
B
Status LED
Blue
- Reset button is pressed when the device is
powered on
Blinking
- Reset button has been released or the
device was powered on without holding the reset
button
C
Video LED
Off
- No video signal detected.
Blue
- Video signal detected.
D
Link TX LED
Off
- No valid connection
Blue
- Valid link
Blinking
- Sending Ethernet Data
E
Link RX LED
Off
- No valid connection
Blue
- Valid link
Blinking
- Receiving Ethernet Data
F
USB
Reserved for future use.
G
System LED Not Used and will remain in the OFF state.
H
USB Host
Reserved for future use.
I
USB HID
Reserved for future use.
J
P1
Reserved for future use.
Networking Guidelines
To ensure that the IP Address will not change due to a power outage,
Savant recommends using DHCP reservation within the router. By
using this method IP Addresses for all devices can be managed from a
single UI, avoiding the need to access devices individually.
NOTE
: IP video device requirements and how to manage IP addresses
are available on the Savant Device Netwoking Guidelines on the Savant
Customer Community.
Additional Information
Refer to the following documents located on the Savant Customer
Community for additional information.
–
Savant IP Video Deployment Guide (009-1977-xx)
–
Savant IP Video Network Configuration Guide (009-1552-xx)
–
Savant IP Audio Deployment Guide (009-1571-xx)
–
Savant Device Networking Guidelines
