PAV-VIMVP1F2-xx/PAV-VIMVP1CP2-xx QRG | 009-2059-00
Copyright 2022 Savant Systems, Inc | 220121
45 Perseverance Way, Hyannis, MA 02601
2 of 2
Rear Panel
Wiring and Connections
IR connection is made using 3.5 mm IR Emit-
ter supplied with the device.
IR Wiring
Enhanced small form-factor pluggable connection. Duplex LC
Multi-mode OM3 Fiber required.
Transport Distance
DAC cable
6ft (2m)
OM3 multi-mode fiber
1000ft (300m)
Optical In (PAV-VIMVP1F2-xx)
RJ-45 10G Ethernet connection.
Transport Distance
Cat6
100ft
(30m)
Cat6a
300ft
(100m)
Cat7
300ft
(100m)
10 GbE (PAV-VIMVP1CP2-xx)
PAV-VIMVP1CP2-xx
DC 12V
IR Out
IR In
A
B
C
HDMI In
D
Loop Out
E
RS232
TX RX G
F
10 GbE (PoE+)
G
Audio
LAN
K
RESET
H
I
L M
J
N
Item
Description
A
Power Input
12V DC
B
IR In
Not used
C
IR Out
3.5 mm IR Emitter connection. Transmits IR
signals via an IR Flasher (5V tolerant) to devices
with an IR input or IR receiver.
D
HDMI In
19-Pin Type A HDMI female digital audio/video
input.
Supports HDMI 2.0a
HDMI 2.0 compliant cable required for 4K
content.
E
Loop Out
Reserved for future use.
F
RS-232
3-pin control connector transmits and receives
serial data to and from serial controllable
devices. For pin-out information, refer to the
RS-232 Wiring
section to the right.
G
10 GbE
10G input from the Audio/Video over IP switch.
SFP+
(PAV-VIMVP1F2-xx)
RJ-45
(PAV-VIMVP1CP2-xx) supports Power
over Ethernet (PoE+ IEEE 802.3at standard).
H
Link LED
Solid Green
- Link is established with
2.5/5GBase-T mode.
Solid Amber
- Link is established with
10GBase-T mode.
Off
– No link established.
I
Link Activity
LED
Amber Blinking
- Indicates data activity.
Off
– No Activity.
J
Audio
3.5 mm (1/8 in) Analog Audio Output.
Outputs 2 Ch PCM audio from the local HDMI
input when 2 CH and MC PCM is present. Does
not support downmixing encoded audio.
Direct Line Level 2.1 VRMS Output.
K
LAN
1G of reserved network data bandwidth
commonly used to connect any network
compliant device to transmit its data onto the
Ethernet network by sharing the 10G network
link. 8-pin RJ-45 female connection.
IMPORTANT!
: Do not connect this port to a
network switch.
L
Link LED
Solid Orange
- Link is established.
Off
– No link established.
M
Link Activity
LED
Amber Blinking
- Indicates data activity.
Off
– No Activity.
N
Reset
Hold down this button with a pointed
stylus for 20 seconds while powering up
the device to restore the device to factory
default settings.
Rear Panel
Power Input
Serial control connection are made
using a 3-pin Control Connector
supplied with the device. The wire slips
into the hole and locks with a screw
located at the top of the connector.
RS-232 Wiring
3
2
1
Rx
Tx
G
PIN 1
PIN 2
PIN 3
Receive
Transmit
Ground
Installation
To install this device use the mounting screws to attach the
included mounting brackets. Please follow the steps below.
1. Align the bracket using the top holes.
NOTE
: This will leave an air gap behind the device.
2. Use mounting screws to attaching the bracket.
If the device is going to be mounted Savant recommends aligning the
device with the rear of the device facing down. This will allow the best
heat dissipation.