PAV-AOM8C | 009-1563-03 | 200110
1 of 2
45 Perseverance Way, Hyannis, MA 02601
Copyright 2020 Savant Systems, LLC
Savant.com | 508.683.2500
Box Contents
(1) 16 Channel Audio Output IP Receiver (PAV-AOM8C-10)
(1) Installation Kit (075-0195-xx)
(2) 3-pin Control Connector (028-9351-xx)
(1) 5V DC 3A Power Supply (025-0153-xx)
(1) Product Insert (009-19xx-xx)
Specifications
Environmental
Temperature
32° to 104° C (0° to 40° C)
Humidity
10% to 80% Relative Humidity (non-condensing)
Dimensions and Weight
Height
1.6 in (4.15 cm)
Width
8.5 in (21.50 cm)
Depth
3.7 in (9.33 cm)
Weight
Net: 1.4 lb (0.64 kg)
Shipping: 2.3 lb (1.05 kg)
Power
Input
5V DC 3A
Maximum
15 Watts
Power over
Ethernet (PoE)
IEEE 802.3af
Networking
Supported
Standard
IEEE 802.1 AVB/TSN switches
IEEE 802.3 Ethernet
Regulatory
Safety and
Emissions
FCC Part 15
CE
C-Tick
RoHS
Compliant
Minimum Supported Release
Savant Software
da Vinci 8.10.1
Network Configuration
To ensure that the IP Address will not change due to a power outage,
a static IP Address or DHCP reservation should be configured. Savant
recommends using DHCP reservation within the router. By using this
method, static IP Addresses for all devices can be managed from a
single UI, avoiding the need to access devices individually.
NOTE
: Setting DHCP reservation varies from router to router. Refer to
the documentation for the router to configure DHCP reservation.
Network Requirements
The PAV-AOM8C requires a Audio Video Bridging (AVB) network.
Connect all Savant devices to the same local area network (LAN) or
subnet as the host. Savant recommends not implementing any type
of traffic or packet shaping in your network topology for the Savant
devices as this may interfere with performance.
Front Panel
Power Status
A B
A
Power LED
Green
: System has power and is operating
normally.
Off
: System is not receiving power.
B
Status LED
Off
: Embedded processor is resetting, or is
powered up, and is booting the embedded
firmware.
Green
: Host has established communications with
the embedded system.
Green Blinking
: Embedded system is ready, but
no communication has been established with the
host.
Red
: Host has determined the firmware needs to
be updated, but a problem occurred during the
process that will initiate a reset.
Red Blinking
: Embedded firmware is running, but
has not received a DHCP IP Address.
Amber
: Host is updating the embedded
firmware.
Amber Blinking
: Embedded system has a valid
link-local IP Address and is connecting to the
host.
Installation
The PAV-AOM8C should be installed on a solid, flat, level surface. The
device will fit on a 1U rack shelf. The location should be dry, well
ventilated, and out of direct sunlight.
IMPORTANT!
The PAV-AOM8C must to be connected to a AVB Switch.
Also a Savant AVB audio input device is required.
Rack
The optional RMB-PAVAM2F-xx or RMB-PAVAM2-xx allows two
devices to be mounted side by side. This rack is compatible with all
standard 19-inch National Electrical Manufacturers Association (NEMA)
rack mounts.
The instructions below show the RMB-PAVAM2F-xx, both brackets
install the same way they just face different directions.
1. Align the bracket with the device’s mounting points.
2. Attach using the screws provided with the bracket.
Savant® ProAV 16 Channel Audio Output IP Receiver with Control (PAV-AOM8C)
Quick Reference Guide
