Saunier Duval Themaclassic F18E SB Скачать руководство пользователя страница 47

Страница: 47 / 52

4000124050-2

18 Replacement of Parts

18.21 (F24E Only) Filling system tap, refer to
diagram 18.12.

Before starting refer to the front of

Section 18 Important

information.

• Remove the front panel

, refer to Section 15.3.

• Lower the control panel

, refer to Section 15.4.

• Drain down the hotwater circuit,

refer to relevant part of

diagram 18.1

• Pull of the filling loop tap extension.

• Pull out slotted metal clip securing tap into housing, remove
tap.

• Pull out slotted metal clip and remove pipe from tap.

18.22 (F24E Only) Reduced pressure zone
valve (RPZ), refer to diagram 18.12.

Before starting refer to the front of

Section 18 Important

information.

• Remove the front panel

, refer to Section 15.3.

• Lower the control panel

, refer to Section 15.4.

• Drain down the boiler only,

refer to relevant part of diagram

18.1

• Pull out slotted metal clip securing pipe to RPZ.

• Pull out slotted metal clip securing RPZ into housing, remove
RPZ.

18.23 Boiler drain point, refer to diagram
18.13.

Before starting refer to the front of

Section 18 Important

information.

• Remove the front panel

, refer to Section 15.3.

• Lower the control panel

, refer to Section 15.4.

• Drain down the boiler only,

refer to relevant part of diagram

18.1

Pull out slotted metal clip securing boiler drain valve into
housing, remove boiler drain valve.

18.24 (F24E Only) Water flow sensor, refer to
diagram 18.14.

Before starting refer to the front of

Section 18 Important

information.

• Remove the front panel

, refer to Section 15.3.

• Lower the control panel

, refer to Section 15.4.

Drain down the hotwater circuit,

refer to relevant part of

Section 18.1

• Undo the union nut on the cold water inlet isolating valve.

• Pull out slotted metal clip securing filling system tap into
housing, swing the tap forwards.

• Pull out the two slotted metal clips retaining the domestic
water inlet filter housing.

• Remove domestic water inlet filter housing.

• Remove electrical connections from water flow sensor.

• Pull off slotted metal clip and remove water flow sensor.

➜

9758

Diagram 18.15

SYSTEM WATER PRESSURE
SENSOR

BYPASS VALVE

9760

Diagram 18.16

AIR
VENT

CAP

Diagram 18.14

WATER FLOW
SENSOR

➜

9765

➜ ➜

F24E only

F24E shown

➜

Содержание Themaclassic F18E SB





















































Результаты поиска

Содержание Themaclassic F18E SB

Отзывы:

Бренды по названию

Популярные бренды

Saunier Duval Themaclassic F18E SB, Инструкция по использованию, установке и обслуживанию

Результаты поиска

Содержание Themaclassic F18E SB

Отзывы:

Бренды по названию

Популярные бренды