SATO 8078-00 Скачать руководство пользователя страница 3

 

Thank you for purchasing the SK-270WP Waterproof Digital Thermometer. 

- This product is designed to measure temperature connecting to a dedicated probe. Do not use it for 

other purposes. 

- Read this manual thoroughly before using the thermometer. Keep the manual in a safe place for future 

references whenever necessary. 

Warning 

The SK-270WP thermometer is not explosion-proof. Never use it in an atmosphere containing 

flammable gases.   

Beware of explosion! 

There is a risk of explosion. Take extreme care. 

 

Whenever you have questions, contact us or the dealer from which the unit was purchased. 

 

 

1. Notes on Use 

Be sure to observe the following precautions in order to use this unit correctly. 

 

- Do not use this unit as a clinical thermometer. 

- Do not drop this unit or apply impact to it. This unit is a precision instrument. 

- Never disassemble or modify this unit. Doing so may result in failure. 

- Do not use this unit in water. 

- Do  not  use  this  unit  in  a place  exposed  to  direct  sunlight  or  near  heating  equipment.  Doing  so may 

result in deformation of the casing or failure. 

- Do  not  use  this  unit  in  an  environment  where  electrical  noise  is  generated.  Doing  so  may  result  in 

unstable display or larger errors. 

- Do  not  forcibly  pull,  bend,  or  bundle  the  sensor  cord.  Placing  a  heavy  object  on  the  sensor  cord, 

heating or scratching the cord may also damage it. 

- If this unit is not to be used for a long time, always remove the batteries from the unit. Otherwise, the 

batteries may leak fluid, resulting in failure. 

- If  the  unit  becomes  dirty,  wipe  it  with  a  tightly  wrung  cloth  that  has  been  dipped  in  warm  water  with 

neutral detergent. Do not wash this unit it in water. 

- Be sure to use this unit within the specified measurement range. Using the unit outside the specified 

measurement range will result in failure or damage.   

- The penetration type probe has a sharp pointed end so that it can penetrate into the measuring object; 

as this pointed end could cause accidental injuries, handle the probe with due care. 

 

 

Содержание 8078-00

















Отзывы: