background image

 

 
- Do  not  touch  the  measurement  window  with  a  sharp  or  hard  object.  Doing  so  may  damage  the  lens, 

causing loss of measurement accuracy.   

 

- Do not use this unit in an environment where electrical noise is generated. Doing so may result in unstable 

display or larger errors. Also, do not bring the unit close to a charged object. 

 
- Never use the unit in water.     
 
- If this unit is not going to be used for a long time, always remove the battery from the unit. Otherwise, the 

battery may leak fluid, resulting in failure. 

 
- Do not dispose of the used battery in a fire. 
 
- Keep the battery out of the reach of children. If you have swallowed the battery accidentally, consult a 

doctor immediately. 

 
- For environmental conservation purposes, dispose of the used battery in compliance with local rules and 

regulations. 

 
- Do not wash or wipe this unit with alcohol, thinner, or other organic solvents. If the unit becomes dirty, 

wipe it with a tightly-wrung gauze or the like that has been dipped in warm water with neutral detergent. 

 
- Do not wipe the temperature measurement section (infrared lens) directly with gauze. For details, refer to 

"Maintenance". 

 
- Glass  does  not  transmit  wavelengths  used  by  this  thermometer.  Therefore,  when  an  object  is  placed 

beyond glass, this unit detects the temperature of the glass and displays its temperature reading. 

 
- If the ambient temperature fluctuates excessively, the measurement accuracy may be affected. Wait for a 

while for the unit to properly adapt to the ambient temperature. For a change of temperature of 10°C or 
more, wait for at least 30 minutes before measurement. 

 
- Never grasp the measurement spot guide (trumpet-shaped section) during measurement, or the 

measurement accuracy may be affected.   

 
   

 

6.    Notes on Storage 

 

-The  storage  ambient  for  the  PC-8400

is  -10  to  50°C  and  less  than  90%RH.  It  is  recommended  to  be 

stored with a desiccant at around room temperature. 

 
- Leaving this unit inside a car under the full sun in a hot climate will cause it to become extremely hot, 

possibly resulting in failure. Do not leave it in such hot places. 

 
 
 

Содержание 1081-00













Отзывы: