manualshive.com logo in svg

Sarlo WeedBoss BC-8, Руководство пользователя, Страница: 5 / 16

Поделиться
Скачать
Sarlo WeedBoss BC-8 Скачать руководство пользователя страница 5

3

ASSEMBLY INSTRUCTIONS

■

TOOL LIST

•  Screwdriver (Phillips or Standard)
•  Allen wrench 4mm
• 10mm wrench

■

INSTALLING CUTTING HEAD

• See page 9 for blade removal instructions.
• Make sure debris shield with line cut off is

properly installed. See next page.

• Lock gear box (3) by inserting a 1/8 in. (4 mm)

allen wrench or pin thru hole and finding
corresponding notch.

• Install splined washer (2) flat side out.
• To install head (1), turn counterclockwise. Hand-

tighten head securely.

• To remove head, turn clockwise

■

INSTALLING THE “J” HANDLE

• Install the clamp assembly on the shaft tube. The

top of the clamp should touch the arrow on the
tube. Leave the screws and nuts slightly loose.

• Place J handle in clamp as shown- The J shape

goes on right side of unit. Position the handle
until the arrow on the handle touches the edge of
the clamp.

• Tighten the screws.

■

THROTTLE–KILL SWITCH

• To accelerate unit hold down lever (3) with the

palm of the RIGHT hand. Then squeeze the
trigger (2).

• To return to idle. Release trigger (2).
• To stop the unit push switch (1) forward.
• To start the unit pull switch (1) back.

■

SHOULDER HARNESS

• Place the strap over your left shoulder and attach

clip to clamp eye on shaft tube.

• Loosen clamp screw and slide clamp up or down

until unit balances with head just touching the
ground.

• Tighten screw.
• Notice quick release feature.

1

2

1

2

3

1

2

3

Содержание WeedBoss BC-8

















Отзывы:

Нет отзывов