Sarlo BigMo 30 inch Скачать руководство пользователя страница 2

OVERVIEW:

 (Fig. 1.) 

1.  Discharge Chute 

2.  Front Height of Cut Adjustment 

3.  Deck Drive Belt Guard 

4.  Operator Presence Control Bale 

5.  Wheel Drive Control Bale 

6.  Engine Throttle Control 

7.  Mower Blade Engagement Control (PTO Switch) 

8.  Ignition Switch 

9.  Engine Pull Start 

10.  Hour Meter 

11.  Hydro Release Lever 

12.  Rear Height of Cut Adjustment 

                      Know Before You Mow!

 

Page 2                                                                                                                                                                             © 2016 Sarlo

®

 Power Mowers, Inc. 

Fig. 1 

WARRANTY:

 

SARLO POWER MOWERS, INC. hereby warrants to the original retail purchaser ALL NEW products of its own manufacture to be free from 
defects in material and workmanship for a period of 

2 years 

from the date of the original purchase, subject to the following conditions: 

1. 

Engines are warranted by the respective engine manufacturer. Refer to the engine manufacturer’s warranty. 

2. 

Transmission parts are warranted by the manufacturer, not Sarlo Power Mowers, Inc. 

3. 

The warranty on belts, tires, throttle controls or any other item that is subject to normal wear is limited to 90 days. 

4. 

No warranty is extended to any equipment which has been misused, neglected or damaged by accident. Sarlo shall not be responsible for 
damage in transit or handling by any common carrier, and under no circumstances, within or without the warranty period, will the company 
be liable for damage for loss, or damages resulting from delay or any consequential damage included but not limited to any cost or     
expense of providing substitute equipment or service during periods of malfunction or non-use. 

5. 

Sarlo Power Mowers will repair or replace, free of charge, any part or parts of the mower found upon examination by any Factory Author-
ized Dealer  or by the factory to be defective in materials and/or workmanship for the term of the warranty. 

6. 

The consumer is responsible for: (1)  Normal maintenance such as greasing, gear case lubrication, minor adjustment and, (2) Transporta-
tion of any Sarlo product to and from the place warranty work is performed. 

7. 

The Sarlo warranty WILL NOT APPLY to any product repaired or altered by anyone other than an Authorized Service Distributor or     
Authorized Service Dealer. 

8. 

Sarlo reserves the right to incorporate any changes in design into its products without obligation to make changes on units previously 
manufactured. 

9. 

The warranty is valid only if the Factory Warranty Card is returned and registered.  

Содержание BigMo 30 inch









Отзывы: