VCC-P7574
VCC-P7575P
Do not touch the lens and lens
tube:
The lens and lens tube are composed of precision
parts that must be strictly kept untouched.
1
Install the base plate on the ceiling or
wall.
1
Make four or two screw hole marks on the ceiling or the wall using the
supplied pattern sheet, and then drill the screw holes.
2
Carry out wiring for the power supply and connected devices inside
the ceiling or wall.
3
Remove the base plate from the camera unit.
4
Draw cables from the power supply and connected devices through
the cable hole
(A1)
,
match the four or two screw holes of both the
base plate and the ceiling or the wall. And then, secure it using the
four or two screws
(B)
through the washers.
2
Make required connections.
Refer to “CONNECTIONS” on the back.
3
Install the camera unit onto the base plate.
Matching the rib
(C1)
of the camera unit base with the rib notch
(C2)
of
the base plate, press the camera unit until it clicks.
4
Check the image from
the camera.
1
Remove the dome cover.
2
Holding in the manner shown on the right, move
the lens in the pan and tilt directions and check the
image on the monitor.
Note:
When the image is displayed upside down, fold the
lens downward and turn it to the left to avoid damage
to the FFC cable.
5
Carry out the settings and adjustment for
the camera using the on-screen menu.
Refer to the separate-volume instruction manual.
Note:
• When monitoring lighting or other extremely bright objects (which
exceed the maximum required illumination), smearing may occur in
the vertical or horizontal direction (either above and below the high-
brightness object or as a perpendicular band). In such a case, adjust
the angle of illumination and other factors while observing the
monitor.
• When installing the camera, make sure to properly perform
waterproofing for the holes in the ceiling or the wall.
• When setting up this camera, make sure that it is installed securely.
Check that the installation location is strong enough to bear the
camera weight before proceeding. Install to the ceiling or a wall that
has no surface unevenness. And be sure to embed the screw into the
ceiling or wall securely. If the screw holes are too shallow, the camera
may fall down. In addition, do not touch the camera unit except when
settings and adjustments are necessary.
• Install where the temperature range will stay between -10°C (14°F)
and 50°C (122°F). (No condensation)
• The camera unit can be installed with the dome cover pointing
upward.
Note:
Make sure that the rib is firmly fixed.
Press and hold the pawl to release the plate.
(B)
(B)
(B)
(B)
(A1)
(A2)
When routing the cables on the ceiling or the
wall, draw the cables between the guides
(A2)
projected from the base plate.
Depth: at least 35 mm
Diameter: at least 3.5 mm - 5.0 mm
(C1)
(A2)
(C2)
When you draw the cables
between the guides
(A2)
,
cut off the tab near the rib
mark on the side of the
camera unit to make the
conduit hole for arranging
the cables.
Tab
Rib mark
Dome cover
Push
You can connect the MONITOR OUT pin and the
GND pin on the base circuit board to a monitor
using an alligator clip cable.
GND
MONITOR
OUT
Rib marks
Camera window
If a whole surface of the camera’s lens does
not show through the camera window, while
holding down the dome cover, turn it
counterclockwise until the whole surface of
the lens appears.
6
Replace the dome cover.
Align the respective rib marks on the camera
unit base and the dome cover, and press the
cover until it clicks.
Hook the FFC cable on
the back of the clamp to
take up the slack.
INSTALLATION MANUAL
Color CCD Camera
●
For the customers in US and Canada
THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE PERSON AND SHOULD CONFORM TO
ALL LOCAL CODES.
☞
Please read this manual before installing and using this camera, and always follow the instructions in it for
proper use.
E
ngl
is
h
L5BK2(INSTALL)(GB).fm 1 ページ ２００６年３月１０日 金曜日 午後１２時１２分
