15
EG
Air Clean Filter
The air clean filter removes dust and dirt from the air, and reduces
odors and smoke from tobacco.
How to install the air clean filter
The air clean filter needs to be installed behind the anti-mold filter.
1.
Remove the anti-mold filter.
2.
Install the air clean filter in the position shown in the figure.
3.
Remount the anti-mold filter.
How to clean the air clean filter
• In general, the filter should be sucked to remove dust in low fan
speed of a vacuum cleaner once every three months.
• If there is heavily grime on the filter, soak the filter in lukewarm
water with neutral detergent diluted 1:500 for 1 to 2 minutes then
wash it.
• Rinse the filter in clean water, then let it dry on the towel in room
temperature.
• Do not bend nor give excessive force onto the air clean filter.
• If the filter surface is heavily blocked with dirt or damaged,
replace it with new one. Purchase a replacement filter at your
local dealer. (model S
Y-22
)
Cleaning the main unit and remote control unit
• Wipe clean using a soft, dry cloth.
• To remove stubborn dirt, moisten a cloth in warm water no hotter
than 40 °C, wring thoroughly, and then wipe.
• The front panel can be removed in order to wash it with water.
TROUBLESHOOTING
If your air conditioner does not work properly, first check the
following points before requesting service. If it still does not work
properly, contact your dealer or service center.
OPERATING RANGE
For Single use:
The air conditioner is operable within the temperature ranges as
listed below:
For Multiple use:
Please refer to “Operating Range” on the sheet attached to the
outdoor unit.
This air clean filter cannot remove
harmful gases or vapors nor ventilate
air in the room. You must open doors
or windows frequently when you use
gas or oil heating appliances.
Otherwise there is a risk of suffocation
in extreme cases.
Air clean filter
NOTE
Trouble
Possible Cause
Remedy
Air conditioner does
not run at all.
1. Power failure.
1. Restore power.
2. Leakage circuit
breaker tripped.
2. Contact service
center.
3. Line voltage is too
low.
3. Consult your
electrician or
dealer.
4. Batteries in remote
control unit have
run down.
4. Replace batteries.
OPERATION lamp
blinks and air
conditioner does not
operate.
Trouble in system.
Contact service
center.
Compressor runs but
soon stops.
Obstruction in front of
condenser coil.
Remove obstruction.
Poor cooling (or
heating)
performance.
1. Dirty or clogged air
filter.
1. Clean air filter to
improve airflow.
2. Heat source or
many people in
room.
2. Eliminate heat
source if possible.
3. Doors and/or
windows are open.
3. Shut them to keep
the heat (or cold)
out.
4. Obstacle near air
intake or air
discharge port.
4. Remove it to
ensure good
airflow.
5. Thermostat is set
too high for cooling
(or too low for
heating).
5. Set the
temperature lower
(or higher).
6. (Outdoor
temperature is too
low for heating.)
6. (Consult your
dealer or try to use
another heat
appliance.)
Clicking sound is
heard from the air
conditioner.
In heating or cooling
operation, any plastic
parts may expand or
shrink due to a
sudden temperature
change. In this event,
a clicking sound may
occur.
This is normal, and
the sound will soon
disappear.
OPERATION lamp
lights but outdoor unit
will not run.
The use of cellular
phones near the air
conditioner may
cause disturbance to
its normal operation.
1. Turn off the power
then restart the air
conditioner after a
while.
2. Consult your
dealer.
Temperature Indoor air
temperature
Outdoor air
temperature
COOLING Max.
32 °C DB /
23 °C WB
43 °C DB
Min.
19 °C DB /
14 °C WB
–15 °C DB
HEATING
Max.
27 °C DB
24 °C DB /
18 °C WB
Min.
16 °C DB
– DB/ –15 °C WB
OI-003-15-EG
01_SAP-KRV186EH_EN.fm Page 15 We dnesday, February 13, 2008 1:12 PM