Page
4
Refer any servicing to qualified personnel.
Do not attempt to remove any screws, or open the casing of the unit; there are no
user serviceable parts inside, refer all servicing to qualified service personnel.
POWER SUPPLY
Connect the mains lead to an AC 240V 50Hz wall outlet.
-- The RADIO ON/OFF switch is mounted on the secondary side. The unit is not
disconnected from the mains even switched off.
BATTERY INSTALLATION
1.
Open the battery compartment cover.
2.
Insert two fresh “AAA” batteries (not included) into the battery compartment,
be sure to follow the polarity (+/-) markings on the bottom of the unit.
3.
Replace the battery compartment cover.
Note:
1. The batteries can also be exhausted and we recommend that you replace the
batteries every year.
2. Please leave the unit connected to the AC outlet while replacing the battery to
avoid losing all of your setting.
Caution
:
All batteries must be installed with the proper polarity (see diagram on the
bottom of the unit).
Do not mix new with old or used batteries.
Only use batteries of the same type and brand.
Remove the batteries to avoid leakage if they are not be used for a prolonged
period.
In the interest of environmental safety, dispose of battery safely.
BATTERY BACK-UP SYSTEM
This unit includes a battery back-up system which protects the clock, sleep timer and
wake-up alarm functions from the mains failure with the battery installed. During the
mains interruption, the clock display will go out, but the clock movement remains in
operation. The time display will be resumed when the mains return.
Reset the time if the display time is incorrect.
When the mains lead is connected to the AC outlet for the first time, or when the
mains returns after a failure longer than the battery life. In this case, set the clock and
alarm again.
ADJUSTING THE CLOCK
1. While holding the
TIME
button down, then press
HOUR
button repeatedly, to set
the correct hour. Be sure to observe the word to confirm that the hour is set
Page
5
correctly.
2. While holding the
TIME
button down, then press
MIN
(Minute) button repeatedly,
to set the correct minute.
3. Release the
TIME
button.
LISTENING TO THE RADIO
1. Set the
RADIO ON/OFF
switch to
ON
(No AUX IN cable insertion).
2. Slide the
BAND
switch to
AM
or
FM
.
3. Turn the
TUNING
control to tune in a station.
4. Adjust the
VOLUME
control as desired.
5. To turn the radio off, set the
RADIO ON/OFF
switch to
OFF
.
.
Aerials
- For
AM
reception, rotate or relocate the unit to a different position to improve the
reception of a distant or weak station.
- For
FM
reception, a short wire aerial is provided. Unwind the short wire aerial
and extend it to full length. You may also have to vary the direction of this
antenna until you find the position that provides the best reception.
SETTING THE ALARM
1. Set the
RADIO ON/OFF
switch to
OFF
.
2.
Set the
ALARM OFF/RADIO/BUZZ
switch to
ALARM-BUZZ
or
ALARM-RADIO
.
Alarm icon
(((
appears.
3. If you set alarm by
BUZZER
, slide
BUZZ SMALL/LARGE
switch to desired
location.
4. While holding the
ALARM
button down,
AL
appears on the top-right of the LCD,
then press the
HOUR
or
MIN(Minute)
button respectively to select the wake-up
time.
5. Release the
ALARM
button.
Note:
If you want to check the alarm time setting, simply push the
ALARM
button.
USING THE ALARM
1. If you want to wake up with the radio, tune in the station and adjust the volume
level first.
2. Set the wake-up time. (See “SETTING THE ALARM”.)
3. Set the
ALARM OFF/BUZZ/RADIO
switch to
ALARM-RADIO
or
ALARM-BUZZ
.
4. The alarm icon
(((
appears on the LCD.
At the preset alarm time, the alarm sounds, then turns off after 1 hour and 59
minutes. The alarm timer will function every day unless
ALARM
switch is set to
OFF
.
To temporarily silence the alarm buzzer or radio, press
SNOOZE
. This silences the
alarm for about 9 minutes. You can repeat this cycle as many times as you like.
To turn off the alarm so it does not sound again, set
ALARM OFF/BUZZ/ RADIO
to
OFF
.
To reset the alarm to sound again at the same time the next day, set it back to
BUZZ
or
RADIO
.
USING THE SLEEP TIMER
1. Set the
RADIO ON/OFF
switch to
OFF
.
2. Push the
SLEEP
button. “00:59” (59 minutes) appears. The radio turns on.
3. Hold
SLEEP
button then press
HOUR
once, the sleep hour digit will be “01”.
4. Hold
SLEEP
button then press
MIN
button repeatedly, the sleep minute digit will
change from 59 to 00. The sleep timer up to 01:59.
5. Release the
SLEEP
button.
6. When the sleep timer is reached, it will turn off the radio automatically. If you
want to cancel the
SLEEP
function when the sleep timer is not reached, press
SNOOZE
button to turn off the radio.
NOTES:
- To release the sleep timer while in operation, set the sleep time to 00:00.
- If you push the
SLEEP
button after sleep time setting, the sleep time will return
to 00:59.
LIGHT HIGH/LOW FUNCTION
Slide
LIGTH HIGH/LOW
switch to select the desired brightness of the display.
AUX IN FUNCTION
1. Set the
RADIO ON/OFF
to
ON
.
2. Connect the external audio equipment to
AUX IN
jack on the back of the unit.
The connection cable is not included.
3. Rotate the
VOLUME
knob to select the desired sound level.
SPECIFICATIONS
Power source: AC: ~240V, 50 Hz
Back-up battery: 2 x 1.5V 2 x ”AAA” size battery (not included)
Power consumption: 3W
Output power: 250 m Watts (AC max.)
Speaker: 16 ohm
Tuning ranges:
AM: 530 – 1620 kHz
FM: 87.5 – 108 MHz
Specifications subject to change without notice.
Made in China
Page
6