Sanyo PLC-XT10, Руководство по обслуживанию

Страница: 50 / 104

-50-
72 PD16/D16/IRQ0 PW_SW Not used -
73 PD15/D15 DATA15 Data Bus 15 - I/O
74 PD14/D14 DATA14 Data Bus 14 - I/O
75 PD13/D13 DATA13 Data Bus 13 - I/O
76 PD12/D12 DATA12 Data Bus 12 - I/O
77 VCC 5V - - -
78 PD11/D11 DATA11 Data Bus 11 - I/O
79 VSS GND - - -
80 PD10/D10 DATA10 Data Bus 10 - I/O
81 PD9/D9 DATA9 Data Bus 9 - I/O
82 PD8/D8 DATA8 Data Bus 8 - I/O
83 PD7/D7 DATA7 Data Bus 7 - I/O
84 PD6/D6 DATA6 Data Bus 6 - I/O
85 VCC 5V - - -
86 PD5/D5 DATA5 Data Bus 5 - I/O
87 VSS GND - - -
88 PD4/D4 DATA4 Data Bus 4 - I/O
89 PD3/D3 DATA3 Data Bus 3 - I/O
90 PD2/D2 DATA2 Data Bus 2 - I/O
91 PD1/D1 DATA1 Data Bus 1 - I/O
92 PD0/D0 DATA0 Data Bus 0 - I/O
93 VSS GND - - -
94 XTAL XTAL X'tal oscillator input - I
95 MD3 Mode3 Multiplex setting with Mode 2 (Set H) I
96 EXTAL EXTAL X'tal oscillator output - O
97 MD2 Mode2 Multiplex setting with Mode 3 (Set L) I
98 NMI CPURESET Non maskarable interrupt input (for manual setting) I
99 VCC (FWP) FWP Write mode for flash memory I
100 PA16/AH FLASH MODE FWP Control O
101 PA17/WAIT Not used O
102 MD1 Mode1 MCU setting with Mode 0 (Set H) I
103 MD0 Mode0 MCU setting with Mode 1 (Set L) I
104 PLLVCC PLLVCC Power supply for PLL -
105 PLLCAP PLLCAP PLL filter -
106 PLLVSS PLLGND Ground for PLL -
107 PA15/CK M-CLK CPU clock output O
108 RES RESET Reset Active L I
109 PE0/TIOC0A/DREQ0 ET7050SCS ET7050 Serial chip select Active L O
110 PE1/TIOC0B/DRAK0 OPT4 XGA/SVGA switch option I
111 PE2/TIOC0C/DREQ1 Not used O
112 VCC 5V - - -
113 PE3/TIOC0D/DRAK1 SDA3 IIC Bus 3 SDA I/O
114 PE4/TIOC1A SCL3 IIC Bus 3 SCL I/O
115 PE5/TIOC1B USB_BRST USB pull-up option resistor on-off O
116 PE6/TIOC2A Not used O
117 VSS GND - -
118 PF0/AN0 KEY1 Key 1 input (A/D input) I
119 PF1/AN1 KEY2 Key 2 input (A/D input) I
120 PF2/AN2 KEY3 Key 3 input (A/D input) I
121 PF3/AN3 OPT1 Destination option1 (A/D input) I
122 PF4/AN4 OPT2 Destination option2 (A/D input) I
123 PF5/AN5 LAMP DET Lamp error detection I
124 AVSS GND Ground for A/D - -
125 PF6/AN6 POWER FAIL Power Fail input (Error at less than 2V) I
126 PF7/AN7 OPT3 Not used I
127 AVREF 5V Reference voltage for A/D I
128 AVCC 5V Power for A/D - I
129 VSS GND - - -
130 PA0/RXD0 PW_RX PW365 Rx Active L I
131 PA1/TXD0 PW_TX PW365 Tx Active L O
132 PA2/SCK0/DREQ0/IRQ0 SEPA_INT Interrupt input from M66230 I
133 PA3/RXD1 RXD RS232C (Control Port)Rx Active L I
134 PA4/TXD1 SH_TXD RS232C (Control Port)Tx Active L O
135 VCC 5V - - -
136 PA5/SCK1/DREQ1/IRQ1 USB INTR USB Interrupt input Active L I
137 PE7/TIOC2B FAN SW FAN ON/OFF switch O
138 PE8/TIOC3A LAMP SW LAMP ON/OFF output Active H O
139 PE9/TIOC3B SDATA OUT 3 Line serial data output O
140 PE10/TIOC3C SCLK 3 Line serial clock output O
141 VSS GND - - -
142 PE11/TIOC3D EXP RESET I/O Expander(M66500FPM) reset output Active H O
143 PE12/TIOC4A R/C remote contol input Active L I
144 PE13/TIOC4B/MRES PW RESET PW365reset signal Active L O
No. Name Function Name Function Polarity I/O
Control Port Functions