Sanyo PDG-DSU30 - 2500 Скачать руководство пользователя страница 38

Страница: 38 / 67

Confidential

4-9

PDG-DSU30

White/Black

4-9 Calibration

1. PC Calibration

Procedure

- Test equipment: video generator

- Once Main Board is changed, PC calibration

should be done as well.
(1) Test signal: 800 x 600@60Hz
(2) Test Pattern: White/Black

- Note

(1) Calibration pattern should be in full screen mode.
(2) Please refer to 4-2 Guide to get into service

mode, then get into “ADC/DEC color”, and choose

“PC Calibration”.

Inspection item

- Check if there is lines on the screen.

- Check if there is noise on the screen.

- Horizontal and vertical position of the video should be

adjustable to the screen frame.

Criteria

- If there is noise on the screen, the product is

considered as failure product.

- The screen appears normal, it shouldn’t appear

any abnormal condition, such as lines and so on.

- Check if the projection is same as monitor diplayed.

2. Video Calibration

Procedure

- Test equipment: video generator.

- Once main board is changed, Video calibration

should be done as well.

(1) Test signal: 480i

(2) Test Pattern: SMPTE BAR

- Note

(1) Calibration pattern should be in full screen mode.

(2) Please refer to 4-2 Guide to get into Service Mode

select ‘‘ADC/DEC color’’, and choose “Video

Calibration”.

SMPTE BAR

Содержание PDG-DSU30 - 2500




































































Результаты поиска

Содержание PDG-DSU30 - 2500

Отзывы:

Похожие инструкции для PDG-DSU30 - 2500

Бренды по названию

Популярные бренды

Sanyo PDG-DSU30 - 2500, Руководство по обслуживанию

Результаты поиска

Содержание PDG-DSU30 - 2500

Отзывы:

Похожие инструкции для PDG-DSU30 - 2500

Бренды по названию

Популярные бренды