Sanyo LCD-24XR12F, Руководство по обслуживанию

Страница: 8 / 37

4.1.4 ADC calibration for Component channel
a) Switch to Component channel;
b) Press key “
INPUT ”, then press digital keys “ 2
、
5
、
8
、
0 ” in turn to enter into primary factory
menu;
c) Move cursor to item “ ADC ADJUST ” and press key “ OK ” to enter into the inferior submenu;
d) Input Component signal ( VG-849 Timing:972(1080i), Pattern:918 100% color bar ); move
cursor to item “ MODE ”, press keys “ ▲ ” and “ ▼ ” to choose item “ YPbPr ”, then move cursor to
item “ AUTO ADC ” and press key “ OK ” to perform auto adjustment until prompt “ success ”
displays;
4.2 White balance adjustment
Unless specified by customer, default settings of COOL color temperature is 12000K and
chromatic coordinates is ( 272
、
278 ); referenced settings of Normal color temperature is 9300K and
chromatic coordinates is ( 285
、
293 ); referenced settings of Warm color temperature is 6500K and
chromatic coordinates is ( 313 、 329 );
Default setting is Normal.
4.3 Adjustment procedures
The TV set should be working above 30 minutes to be in a stabler state before adjustment. Use
CA-210 BBY channel to adjust white balance;
a) Switch to HDMI channel;
b) Press key “
INPUT ”, then press digital keys “ 2
、
5
、
8
、
0 ” in turn to enter into primary factory
menu;
c) Move cursor to item “ W/B ADJUST ” and press key “ OK ” to enter into the inferior submenu;
d) Input HDMI signal ( VG-849 Timing:
972
(10
80i
)
，
Pattern: 921 16 step Gray );
move cursor to item “ MODE ”, press keys “ ▲ ” and “ ▼ ” to choose item “ HDMI ”, then move
cursor to item “ TEMPERTURE ” and press keys “ ▲ ” and “ ▼ ” to choose “
NORMAL
”;
e) Fix “ G GAIN ”, adjust “ R GAIN, B GAIN ” to set 14
th
chromatic coordinates as (
285
、
2
93
);
f) Fix “ G OFFSET ”, adjust “ R OFFSET
、
B OFFSET ” to set 4
th
chromatic coordinates as
(2
85
、
2
93
);
g) To make sure chromatic coordinates of bright scale are ( X=2
85
±10 ， Y=2
93
±10 ) and
chromatic coordinates of dark scale are ( X=2
85
±10
，
Y=2
93
±10 ) during adjusting;
h) Move cursor to item “ COPY ALL ” to copy white balance data to other channels except DTV
channel;
i) Check if chromatic coordinates of
COO
L and WARM meet the requirements (permitted
error of
COO
L bright scale: x±10 ， y±10 , permitted error of
COO
L dark scale: x±10 ，
y±10 ; permitted error of WARM bright scale and dark scale: x±10
，
y±10 ); if not, adjust
“ R_GAIN /B_GAIN/R_OFF/B_OFF ” to be up to the requirements and then save the data;
j) Perform “ Copy All ” for
COO
l/Warm adjustments except DTV channel;
k) Check if chromatic coordinates of other channels meet the requirements, if not, do
adjustment for nonstandard channel alone with the same procedures from b) to j) as HDMI
channel’s and then save the data;
l) Switch to
DTV
channel, change to 16-grey-scale program from central signal source,
adjust white balance with the same procedures from e) to g) ; but pay
attention not to
perform “COPY ALL”!
m) Inspect all channels after completing adjustment to check if display is normal;
n) Refer to the following rule for adjustment: