SERVICE ADJUSTMENTS (Continued)
— 6 —
ANTENNA CONNECTIONS
This receiver is designed for UHF/VHF reception. A 75 ohm
terminal is provided for UHF and VHF receptions. When
connecting a CATV antenna system, connect the 75 ohm
coaxial cable directly to the 75 ohm terminal. For 300 ohm
VHF antenna, use an adapter (not included with the TV set).
CIRCUIT PROTECTION
Fuse F601 (4A) is included in the AC line. This fuse must be
replaced with the proper fuse (see Parts List).
+B VOLTAGE CHECK
Connect Vol lead to TJ1 130V and – lead to ground
(TE7). Connect receiver to AC 120V line. Tune receiver to an
active channel. Reset the picture controls to the FACTORY
PRESET levels (press remote control RESET key twice).
Voltage must measure b128.0V and 132.0V. If the
voltage is out of this range, the power circuit must be
checked. No +B adjustment is provided on this chassis.
HORIZONTAL WIDTH ADJUSTMENT
1. Tune receiver to an active channel.
2. Adjust H-Width Control (VR461) for proper width.
3. Select several other channels and check width.
HORIZONTAL CENTERING ADJUSTMENT
1. Tune receiver to an active channel.
2. C hec k that picture is in the horizontal center of TV
screen.
If picture is not centered horizontally, perform steps 3 ~ 6.
3. Turn off the receiver and disconnect the AC power cord
(120V AC line).
4. While pressing the MENU key, reconnect the AC power
cord. The Service Menu display will now appear.
5. Select NO. 01 HP (Horizontal Phase) with
▲
or
▼
key.
6. Adjust the data with + or – key for proper horizontal
center. To turn off the Service Menu display, press the
MENU key.
VERTICAL SIZE ADJUSTMENT
1. Tune receiver to an active channel.
2. Check the vertical size of the picture. If the vertical size is
too large or small, perform steps 3 ~ 6.
3. Turn off the receiver and disconnect the AC power cord
(120V AC line).
4. While pressing the MENU key, reconnect the AC power
cord. The Service Menu display will now appear.
5. Select NO. 07 VS (Vertical Size) with
▲
or
▼
key.
6. Adjust the data with + or –key for full scan. To turn off the
Service Menu display, press the MENU key.
VERTICAL CENTERING ADJUSTMENT
1. Tune receiver to an active channel.
2. Chec k that picture is in the vertical center of TV screen. If
picture center is too low, replace resistor R513 (1K ohm,
1/2W) with 470 ohm, 1W resistor. If picture center is too high,
remove resistor R513 (1K ohm, 1/2W).
GRAYSCALE ADJUSTMENT
1. Set the picture controls to the Sports levels or Reset
(use MENU key and
▲
or
▼
key or RESET key).
2. Turn off the receiver and disconnect the AC power cord
(120V AC line).
3. While pressing the MENU key, reconnect the AC power
cord. The Service Menu display will now appear.
4. Select NO. 08 RB (Red Bias), NO. 09 GB (Green Bias),
and NO. 10 BB (Blue Bias) with
▲
or
▼
key and set each
data to 0 with + or – key.
5. Select NO. 11 RD (Red Drive) and NO. 12 BD (Blue Drive)
with
▲
or
▼
key and set each data to 60 with + or – key.
6. Set NO. 21 GD (G Drive Reduction) data to 7, NO. 25 SB
(Sub-Brightness) data to 32, NO. 26 SCO (Sub-Color)
data to 10, NO. 27 STI (Sub-Tint) to 17 and NO. 28 SSH
(Sub-Sharpness) data to 8 with
▲
or
▼
, and + or – keys.
7. Turn Screen Control (T402) to minimum (fully counter-
clockwise).
8. Select the Service Menu NO. 41 (Bias Adjustments) with
▲
or
▼
key.
9. Advance Screen Control (T402) clockwise to obtain just
visible one color line. If line does not appear, place this
control to maximum (fully clockwise).
10. Raise each Bias Level with 3, 6, and 9 keys to obtain just
visible white line. (See Figure 4 below.)
11. Select the Service Menu NO. 40 DRV (Drive Adjustments)
with
▲
or
▼
key.
12. Adjust Red and Blue Drive Levels alternately with 1, 3,
7, or 9 key to produce normal black and white picture in
highlight areas. (See figure 5 below.)
13. Check for proper grayscale at all brightness levels.
To turn off the Service Menu display, press the MENU
key.
Note: If Grayscale Adjustment is made after picture tube
replacement, check Brightness Level Adjustment.
FOCUS ADJUSTMENT
Adjust focus control (T402) for well defined scanning lines.
CAUTION
FOR CONTINUED PROTECTION AGAINST
A RISK OF FIRE, REPLACE ONLY WITH THE
SAME TYPE 4A, 125V FUSE.
1
2
3
4
5
6
7
9
8
RB(–)
RB(+)
BB(–)
BB(+)
(N/A)
GB(–)
(N/A)
GB(+)
(N/A)
FOR RED BIAS ADJUSTMENT
FOR BLUE BIAS ADJUSTMENT
FOR GREEN BIAS ADJUSTMENT
Figure 4. Remote Control Number keys’ function in Service
Menu NO. 41
1
2
3
4
5
6
7
9
8
RD(–)
RD(+)
BD(–)
BD(+)
(N/A)
(N/A)
(N/A)
(N/A)
(N/A)
Figure 5. Remote Control Number keys’ function in
Service Menu NO. 40 DRV
FOR RED DRIVE ADJUSTMENT
FOR BLUE DRIVE ADJUST-
