8
OPERATING THE UNIT
Before operating the unit for the first time, make sure the AC power cord is properly connected to a 240V 50Hz
AC outlet, then press the power ON switch on the rear of the unit, the unit will be in standby mode, the backlight of
standby is red. You can now press the STANDBY/ON button on the unit or press the STANDBY/ON button on remote
control to switch the unit ON. The backlight of the standby will be off and multi function touch plate will light on blue.
Pull the AC plug out of the wall socket if you want to switch off completely.
STANDBY/ON
1. Press the
STANDBY/ON
button on the unit or
remote control
to switch the unit on.
2. Select the sound source (CD, USB, CARD, iPod, AUX or TUNER) by touching the FUNC on the unit
or press the
FUNCTION
button
on remote control
. The corresponding display will light up.
3. Adjust the volume with the VOL or VOL on the unit or remote control.
4. Press the
STANDBY/ON
button
on the unit
or remote control
again to turn off the unit.
Note:
1. During in standby mode, press any button/key can make the display light for 10 seconds.
2. Please turn the main switch off to save energy, when you do not use the unit.
During in the STANDBY mode.
1. Press and hold the iPod/MEM/C-ADJ. button until the time displays will change to 24-hour format and flash.
2. Touch or on the unit
or press
or
button on the remote control
to select 12-hour or 24-hour.
3. Press the iPod/MEM/C-ADJ. button again, the HOUR digit will flash on the display, touch or to adjust
HOUR.
4. Press the iPod/MEM/C-ADJ. button once more, the MINUTE digit will flash on the display, touch or
to adjust minute.
5. Press the iPod/MEM/C-ADJ. button again to confirm the time.
6. Each enable state as shown above will be cleared if the key is not pushed in10 seconds.
CLOCK SETTING
TIMER SETTING
1. After adjusting the clock, press the TIMER button for a few seconds, " ON" and "00:00" appear on the display and
the HOUR digit flashes.(F1)
2.
Touch
or
on the unit
or press
or
button on the remote control to adjust it.
3. Press the TIMER button again, the MINUTE digit will start flashing, adjust it by t
ouch
ing
or
on the unit or
press
or button
on the remote control.
4. Press the TIMER button once more to confirm and order TIMER ON time.
5. After adjusting "TIMER ON", " OFF" appears on the display and the HOUR digit flashes.(F2)
6. Repeat the above steps 2 to 3, and then press the TIMER button once more to confirm and order TIMER OFF time.
7. Now the "TUNER" appears on the display with flashing, and then select the alarm mode of the “
TUNER, CD, USB,
CARD or IPOD
" by t
ouching
or on the unit
.
8. Press the TIMER button again, the timer "VOL" indicator appears on the display and flashes, adjust the timer
volume high or low by t
ouch
ing
or
on the unit
or press the
or
button on the remote control.
9. Each enable state as shown above will be cleared if the button is not pushed in 10 seconds.
10.After adjusting "TIMER ON" and "TIMER OFF", press the TIMER button, " “ appears on the display.
11.The main unit will be switched on automatically at "TIMER ON" order and start playing, the main unit will be
switched off automatically at "TIMER OFF" order.
Note: If the display shows "ERROR" while you set the “TIMER ON”, it means both “TIMER ON” and “TIMER OFF” is
the same. In this case, please go to “TIMER OFF” to set the off time first. To switch TIMER function ON or OFF,
press TIMER button.
