E7
Dialing a Stored Number
To dial a phone number stored in memory, press
TALK/END
, then press
MEMORY
and the memory
location (0–9) number. Your phone will dial the
stored number.
If you select a memory location that
does not have a stored number, the
handset will beep rapidly and the phone
will not dial.
Mute
You can turn off the handset microphone while you
are on the phone, so that your calling party cannot
hear you.
1
Press
MUTE
during a telephone call.
The microphone is turned off.
2
To cancel mute, press
MUTE
or
TALK/END
.
Chain Dialing
You can store a special access code, a number to
access banking transactions, for example, and then
use chain-dialing to facilitate your operation.
1
Store the access code into one of the memory
locations (0–9).
2
Dial the main number.
3
Press
MEMORY
and the memory location of
the access code at the appropriate time.
Erasing a Stored Number
1
Remove the handset from the base.
2
Press
MEMORY
twice.
3
Press the memory location number (0–9) you
want to clear. You hear a long beep confirming
that you have erased the number.
Replacing a Stored Number
Your phone has 10 memory locations, represented
by the numbers 0–9 on the keypad. If you store a
phone number in one of these locations and
attempt to store a different number in the same
location later, the new number will replace the pre-
vious one.
Selecting a Different Channel
If you encounter interference while using your
phone, you can manually change the channel for
clearer communication by pressing the
SCAN
but-
ton. This function works only when the phone is in
use.
Interference can come from appliances or other
phones in your home.
The
SCAN
button on the handset allows you to
choose from 20 factory-set channels. During the
course of a conversation, if you hear static or noise
which makes it difficult to hear, press
SCAN
. The
TALK/BATT LOW
indicator flashes, indicating the
phone is changing to another channel.
Using the Flash Button
Use
FLASH
for accessing special services* offered
by your local telephone company, such as Call
Waiting. If you receive a call during your conversa-
tion, press the
FLASH
button on the handset. Press
FLASH
again to return to the previous call.
*Subscription required.
Using the Page/Find Feature
The Page/Find feature sends a signal from the base
to the handset causing it to beep. This is useful for
locating the handset when it is away from the base.
To use this feature, press
PAGE/FIND
on the base
for less than 2 seconds. The handset beeps for 5
seconds. Press
PAGE/FIND
more than 2 seconds to
within a minute, the handset beeps for a minute.
(Press and hold the
PAGE/FIND
button for more
than 1 minute to get a continuous beep.)
The paging feature does not work
when the phone is in use.
On the handset, press any key except
TALK/END
and
SPEAKER
to end the page. If you want to end
the page and make a call, press
TALK/END
or
SPEAKER
.
Press
TALK/END
or
SPEAKER
again if you do not
wish to make a call.
Travelling Out of Range
When you begin to move too far from the base, you
will first hear a clicking sound. As you travel further
out of range, the voice transmission will begin to
break up.
If you pass the range limits of the base, your call will
terminate.
HandsFree Speakerphone in the Handset
• Press
SPEAKER
during a call to switch to HandsFree conversation
using the handset speakerphone.
• Press
TALK/END
to return to normal conversation using the
earpiece speaker, or
SPEAKER
to hang up.
CLT9930 (SANYO) A5 2nd 6/27/00 6:42 PM Page 8
