14
PICTURE-IN-PICTURE (PIP) OPERATION
For PIP to function you must connect two signals to the TV. (Use the TV’s 75 ohm input and
A/V inputs.) Connect VCR (or other accessory equipped with a video output jack) to the
TV’s audio video jacks as shown on page 12. If you are using a satellite dish, you must
connect two receivers or a cable system or antenna with the satellite to use the PIP feature (see
page 13). For operation with Cable Box, see chart on page 15.
USING PIP TO VIEW TWO TV PROGRAMS
Note: The following steps correspond to numbers on the
art below.
1. Switch VCR and television ON.
2. Press
PIP ON/OFF
key.
Set VCR to
TV
mode, if necessary.
3. Select channel for big window.
4. Press
SELECT
key to select Video1 or Video2 screen.
5. Press
VCR
key.
Note: If the remote control cannot be programmed to operate your VCR, you must use the
VCR’s remote to perform VCR functions.
6. Select channel on VCR for small window.
USING PIP TO VIEW TV PROGRAM
AND PRERECORDED TAPE
Note: The following steps do not have corresponding
reference numbers on the remote control art.
1. Set TV channel to match output of VCR (Channel 3 or 4).
2. Insert prerecorded tape into VCR.
3. Press
PLAY
, if necessary (wait for tape to load).
4. Set VCR to
TV
mode.
Note: When the remote control is in the VCR mode, the
VIDEO MODE
key works like the
TV/VCR
key
on the VCR.
5. Press
SWAP
key to view PIP image in big window.
QuickTips
■
PIP window is black
with no
picture:
1. Check cable
connections.
2. Make sure VCR is
turned on.
3. Select another
channel on your
VCR.
■
Same picture appears
in Big and Small
windows. Set VCR
to TV mode.
■
To view two TV
programs or watch
a TV program and
prerecorded tape at
the same time, follow
steps on this page
and chart on page 15.
PIP KEYS
■
Use the
SWAP
key to
exchange programs
between the windows.
■
Use the
LOCATION
key to change the
position of the small
window (Top: L /R or
Bottom: L /R).
■
Use the
QUIKFREEZE
key to stop the
action (see page 15).
■
Use the
SELECT
key
to choose the PIP
video source (Video1,
Video2, or TV RF
Signal).
VCR set to VCR mode.
Same image appears in
both windows.
VCR set to TV mode.
Different images appear
in each window.
CH
MENU
RECALL
CAPTION
SLEEP
1
4
7
0
8
5
2
3
6
9
RESET
VIDEO
MODE
POWER
CABLE
VCR
TV
REC
STOP
PAUSE
PLAY
MUTE
DISPLAY
VOL
VOL
V-GUIDE
PIP ON/OFF
SWAP
LOCATION
SELECT
QUIK
FREEZE
❺
❸
❻
❷
❹
❶
(Continued on page 15.)
PICTURE-IN-PICTURE (PIP) OPERATION
For PIP to function you must connect two signals to the TV. (Use the TV’s 75 ohm input and
A/V inputs.) Connect VCR (or other accessory equipped with a video output jack) to the
TV’s audio video jacks as shown on page 12. If you are using a satellite dish, you must
connect two receivers or a cable system or antenna with the satellite to use the PIP feature (see
page 13). For operation with Cable Box, see chart on page 15.
USING PIP TO VIEW TWO TV PROGRAMS
Note: The following steps correspond to numbers on the
art below.
1. Switch VCR and television ON.
2. Press
PIP ON/OFF
key.
Set VCR to
TV
mode, if necessary.
3. Select channel for big window.
4. Press
SELECT
key to select Video1 or Video2 screen.
5. Press
VCR
key.
Note: If the remote control cannot be programmed to operate your VCR, you must use the
VCR’s remote to perform VCR functions.
6. Select channel on VCR for small window.
USING PIP TO VIEW TV PROGRAM
AND PRERECORDED TAPE
Note: The following steps do not have corresponding
reference numbers on the remote control art.
1. Set TV channel to match output of VCR (Channel 3 or 4).
2. Insert prerecorded tape into VCR.
3. Press
PLAY
, if necessary (wait for tape to load).
4. Set VCR to
TV
mode.
Note: When the remote control is in the VCR mode the
QuickTips
■
PIP window is black
with no
picture:
1. Check cable
connections.
2. Make sure VCR is
turned on.
3. Select another
channel on your
VCR.
■
Same picture appears
in Big and Small
windows. Set VCR
to TV mode.
■
To view two TV
programs or watch
a TV program and
prerecorded tape at
the same time, follow
steps on this page
and chart on page 15.
PIP KEYS
■
Use the
SWAP
key to
exchange programs
between the windows.
■
Use the
LOCATION
MENU
RECALL
CAPTION
SLEEP
1
4
7
0
8
5
2
3
6
9
RESET
VIDEO
MODE
POWER
CABLE
VCR
TV
❺
❻
❶
