Clean washing machine
Use soft clothing to wipe off the water or
dirt on the surface of the washer.
● Detergent, propellant and other
chemicals are not allowed to use
to avoid the damages
on the surface.
● Do not spray water
directly to the washer
body.
1.During Washing or Rinsing, still there is Water inletting. This is possibly automatic water
adding due to water level decrease.
2.Spin tub turns or stops timely at the beginning of spinning. This is intermittent spinning
for better spin effect.
3.No drainage during overflow rinse. This is caused by lower water level set or lower
water pressure.
4.Water inletting and rinsing sometimes during spinning. This is automatic lean-correction
due to clothe is not equally inside.
5.There is sound like water flow after spinning. This is the sound of balance liquid in
Balance ring. It is for reducing vibration of spinning.
6.Control panel keeps warm after power off, this is caused by Remembering circuitry
working.
7.Power off during working and the washer could not continue working. Should set the
program again.
NO TROUBLE CONDITIONS
NO TROUBLE CONDITIONS
TROUBLE SHOOTING GUIDE
TROUBLE SHOOTING GUIDE
Trouble Indication
When the following problems occur,the microcomputer will detect the abnormal condition
and an electronic buzzer sounds for approximately 10 seconds and the indicators flash as
shown below. At the same time,the washer stops operation.
Kind of
Trouble
Trouble
Indication
Where to Check
The washer
does not work
at all.
Press the POWER ON/OFF button.
Press the START/PAUSE button.
Press the PRESET button.
Check whether power failure occurs.
Check whether the fuse or circuit breaker has
been activated.
Water does not
flow into the
Wash/Spin Tub.
Water does not
drain out.
The washer
does not spin.
The buzzer
keeps beeping.
Other troubles.
Close the Washer Lid.
Check whether the CHILD LOCK is set.
Close the Washer Lid.
Turn the water supply faucet on.
Check whether the water supply has been cut off.
Check whether the metal filter of the Water Inlet
is clogged.
Check the washer has been freezing.
water pressure is too low.
Check whether
Put down the Drain Hose from the hookhole.
Check the Drain Hose for any obstructions.
Check whether the Drain Hose is clogged.
Check whether the Drain Hose rises too high off
the ground.
Check whether the laundry is clumped on one
side of the Wash/Spin Tub.
Check whether the washer is on the level surface.
Press the POWER ON/OFF button to turn off the
power, call your service-person or dealer.
NOTE:
The trouble indicators can be released by pressing the START/PAUSE button
once if you want to release the emergency stop.
Then press the START/PAUSE button again to restart the operation.
Filter
Water Inlet
If a malfunction should occur during the washer operation,first check the
following items before calling a service-person or dealer.
WARNING
WARNING
17
17
18
18
Below introducing how to maintain the washing machine
Below introducing how to maintain the washing machine
Clean lint filter
(Suggest clean it every week)
1.Take out the lint filter.
2.Pull out the scraps and wash
the lint filter in the water.
3.Install the Filter ( aim the
frame claw to the groove
below).
( Lint Filer is easy destroyed
parts).
Clean “ magic ” hose joint filter
“ Magic ” Hose
Joint filter
“ Magic ”
Hose Joint filter
(Suggest clean it every 6 months)
1.Pull the water inlet hose out.
2.Turn off the revolver
according to below photo.
3.Load off the
and clean the crud
with a toothbrush.
4.Install the clean
to revolver
and water inlet hose
Clean the water inlet Valve
(Suggest clean it every 6 months)
After long time use, the water inlet
mesh bag may be blocked with
crud, please load off the water
inlet hose, take out the water
inlet mesh bag from the water
inlet valve, clean the mesh bag,
then assemble the mesh bag in
the valve and load the water
inlet hose.
CARE AND MAINTENANCE
CARE AND MAINTENANCE
