!
●About BIND : each 2.4GHz transmitter has ID Number. The bind is stored ID Number in receiver.
If receiver bind with transmitter, receiver will be worked by only the transmitter.
1. Please set [RF mode] is [FH5] in
T
ransmitter System (Compatible with FH5 as M17)
2.
T
urn on the transmitter, and set for other devices as response mode. Then, enter [BIND] to be bind mode.
3. Connect BIND plug in RX-491 BIND/SS
L
port. Then, turn on receiver.
*When you bind transmitter with the receiver, please connect battery in empty port. (In case of EP car, speed controller connect in CH2 port)
4. After RX-491 LED will be changed fast flashing blue from slow flashing blue, please take off BIND plug and restart RX-491 (
T
urn off receiver, then turn on).
5. Please finish BIND mode on transmitter to use enter/back operation by touch pad. In case of binding with transmitter, LED on the receiver turn on blue.
Please operate device as servo to check BIND is completed.
* In case of turning off LED in the process or did not complete BIND setting, please reset binding form 2. in bind process.
■ Default is not bind with transmitter. Please bind with transmitter before using
.
■ MUST use the receiver with bound transmitter.
！
● Please mount the antenna of receiver as high as possible in your model.
● Do NO
T
cut off the antenna and bundle the antenna.
● Stand antenna vertically. Please place receiver apart from motor and FE
T
Speed Controller (include leads).
● Please check surely connection devices as servos and switch with the receiver. In case of loosing connection during running,
it is possible to be out of control.
● The receiver is weak in extreme vibration, shock, and water. Please take care of vibration, shock, and water.
● Please mount the receiver apart from carbon and metal chassis.
● Metal to metal contact in your model will generate to noise. It will interfere the receiver ability and is possible to be out of control.
● Please take noise killer condenser to brushless motor for RC car. If not taking noise killer condenser to brushless motor for RC car
,
noise will be generated. It is possible to be out of control.
● Please use transmitter, servos, FE
T
speed controller made by SAN
W
A.
*in case of combine to use with the devices except SAN
W
A devices, we could not take responsibility for any failures.
●About RX-491
RX-491 can store 2 transmitter ID Number. It is able to combine using individual transmitter which is different setting in endurance race .
If you bind with 2 different transmitter, the receiver store the different transmitter and can operate by transmitters without re-bind.
*CANNOT operate by the 2 different transmitter at the same time. 2 ID store system is only compatible with M17.
- Throttle neutral position or operation quantities might be different each transmitter. Please adjust each transmitter setting to fit chassis linkage.
- MUST set fail-safe setting on each transmitter.
- Please set same RF mode and response mode as 1st transmitter when you bind 2nd transmitter. If it was different mode, cannot bind with 2 transmitters.
*If 2nd transmitter was different RF node and response mode from 1st transmitter, 1st transmitter ID No. is deleted and only write 2nd transmitter.
*If you bound 3rd transmitter, 1st transmitter ID No. will be deleted.
Connect Bind Plug
to the Bind Port
Turn on Battery Switch!
Turn on receiver or
speed controller switch
BIND Plug
⇒
Binding operate (Flash for a second)
Receiver LED Condition
Take off BIND Plug
and restart receiver
BIND Complete (Fast Flashing for 0.1 second)
・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・
・・・・・
How to Bind with Transmitter
*Did not connect anything above picture
but please connect device as servos or
FET speed controller (except motor)
when you bind
Finish Bind Mode
on transmitter (M17)
Turn on LED
PRECAUTION FOR SAFE USE
WARNING
WARRANTY AND SERVICE INFORMATION
SANWA Electronic Instrument CO., LTD
1-2-50 Yoshida-Honmachi
Higashi Osaka, 578-0982 JAPAN
Telephone : 81-72-962-1277
FACSIMILE: 81-72-964-2831
Your RX-491 is warranted against manufacture defects in materials and workmanship.
This warranty does not cover suitability for specific application, components worn by use or improper voltage,
tampering, modification, misuse, abuse, improper wiring, reverse polarity, moisuture damage or acts of Gods.
For warranty and service information, please contact the SANWA distributors in your region.
For a list of distributors in your region, please visit www.sanwa-denshi.com/rc/distributors.html.
ENTER